Design od a connected pipe test facility for ramjet applications

Download
index.pdf
2005
Sarışın, Mustafa Nevzat
Show full item record
265
views
172
downloads
Development of the combustor of a ramjet can be achieved by connected pipe testing. Connected pipe testing is selected for combustor testing because pressure, temperature, Mach number, air mass flow rate can be simulated by this type of testing. Real time trajectory conditions and transition from rocket motor (booster) to ramjet operation can also be tested. The biggest advantage of connected pipe testing is the low operation cost and simplicity. Air mass flow rate requirement is less than the others which requires less air storage space and some components like supersonic nozzle and ejector system is not necessary. In this thesis, design of a connected pipe test facility is implemented. Three main systems are analyzed; air storage system, air heater system and test stand. Design of air storage system includes the design of pressure vessel and pressure & flow regulation system. Pressure and flow regulation system is needed to obtain the actual flow properties that the combustor is exposed to during missile flight. Alternatives for pressure and air mass flow rate regulation are considered in this study. Air storage system designed in this thesis is 27.8 m3 at 50 bar which allows a test duration of 200 seconds at an average mass flow rate of 3 kg/s. Air heater system is utilized to heat the air to simulate the aerodynamic heating of the inlet. Several different combustion chamber configurations with different flame holding mechanisms are studied. The most efficient configuration is selected for this study. Combustion analysis of the air heater is performed by FLUENT CFD Code. Combustion process and air heater designs are validated using experimental data. Designed air heater system is capable of supplying air at a temperature range of 400-1000 K and mass flow rate range of 1.5-8 kg/s at Mach numbers between 0.1-0.5 and pressure between 2-8 bar. Finally the design of the
Machine design and drawing.
http://etd.lib.metu.edu.tr/upload/12606078/index.pdf
https://hdl.handle.net/11511/15098
Graduate School of Natural and Applied Sciences, Thesis

Suggestions

Extra Korolev producers: their impact on production
Yskak, Aidos; Parlaktuna, Mahmut; Department of Petroleum and Natural Gas Engineering (2010)
In this study, a three-dimensional, three-phase dynamic simulation model based on geological investigations of Korolev oilfield in Kazakhstan was used as a development planning tool in order to improve performance of three new wells. The model, developed previously by means of a seismic study, well log and core data, incorporating with characteristics of oilfield productivity, properties of reservoir, liquids and gases that are saturating the hydrocarbon-bearing horizon can be used to calculate development ...
Modeling of Multi Open Phase Fault Condition of Multi-phase Permanent Magnet Synchronous Motors
Fei, Marco; Zanasi, Roberto (2011-09-10)
This paper deals with the modeling of multi-phase permanent magnet synchronous motors under multi open phase fault condition. The presented model is suitable for generic number of phases, generic shape of the rotor flux and generic number of open circuit faults. The motor model in fault condition can be used for faults occurring on both adjacent and not adjacent phases. The model can be very useful both for simulation and implementation of fault-tolerant control strategies.
Pseudo-dynamic testing of a concrete gravity dam
Aldemir, Alper; Binici, Barış; Arıcı, Yalın; Kurç, Özgür; Canbay, Erdem (2015-09-01)
Inspired from the simplified single degree of freedom modeling approach used in the preliminary design of concrete gravity dams, a pseudo-dynamic testing method was devised for the seismic testing of a concrete gravity dam section. The test specimen was a 1/75 scaled section of the 120-m-high monolith of the Melen Dam, one of the highest concrete gravity dams to be built in Turkey. The single degree of freedom idealization of the dam section was validated in the first stage of the study using numerical simu...
Design, Modeling, and Control Allocation of a Heavy-Lift Aerial Vehicle Consisting of Large Fixed Rotors and Small Tiltrotors
Ozdogan, Gokhan; Leblebicioğlu, Mehmet Kemal (2022-02-01)
In this article, we propose an unconventional heavy-lift aerial vehicle (HLAV), present the design and its control allocation analysis, and prove the concept by the demonstration of the experimental test prototype in the outdoor environment. We aim for a mechanically robust and simple vehicle design that efficiently performs heavy lifting compared to other common aerial vehicles under certain width constraints, without using a complex swashplate mechanism. The HLAV performs the task of carrying the main loa...
Design and Experimental Investigation of a Wind Tunnel Gust Generator
Yığılı, İmge; Andırın, Mert Ali; Kurban, Erk; Başkan Perçin, Özge; Perçin, Mustafa (2021-09-10)
This work aims at developing a two-vane gust generator for a small size open-loop wind tunnel to study the unsteady aerodynamic response of lift producing test models. The focus of the study is two-fold: (1) the design of a gust generator which produces the desired gust profiles by varying the parameters such as flow speed, pitching frequency of the vanes, maximum angle of deflection of the vanes and spacing between the vanes and (2) the experimental investigation of the gust velocity profiles via particle ...
Citation Formats
M. N. Sarışın, “Design od a connected pipe test facility for ramjet applications,” M.S. - Master of Science, Middle East Technical University, 2005.
METU IIS - Integrated Information Service open@metu.edu.tr