Show/Hide Menu
Hide/Show Apps
Logout
Türkçe
Türkçe
Search
Search
Login
Login
OpenMETU
OpenMETU
About
About
Open Science Policy
Open Science Policy
Communities & Collections
Communities & Collections
Help
Help
Frequently Asked Questions
Frequently Asked Questions
Guides
Guides
Thesis submission
Thesis submission
MS without thesis term project submission
MS without thesis term project submission
Publication submission with DOI
Publication submission with DOI
Publication submission
Publication submission
Supporting Information
Supporting Information
General Information
General Information
Copyright, Embargo and License
Copyright, Embargo and License
Contact us
Contact us
Lap splice behavior and strength of cfrp rolls
Download
index.pdf
Date
2008
Author
Taşlıgedik, Ali Şahin
Metadata
Show full item record
Item Usage Stats
123
views
30
downloads
Cite This
Behavior of lap splices formed by CFRP rolls has been studied. CFRP rolls have been prepared by using CFRP sheets of a certain width. Strengthening methods that use CFRP rolls as reinforcement may require an epoxy anchored lap splice due to the conditions at the strengthening regions. It may not always be possible to strengthen the region by using only one roll fan anchored at both ends, but using two rolls from opposite faces of the member and lap splicing them at the middle so that they act as a single roll. Lap splice behavior can be studied best by using flexural beam bond specimens if the reinforcing material is steel. Therefore, it has initially been suggested that flexural beam specimens reinforced for flexure with CFRP rolls as tension reinforcement can be used in studying the lap splice behavior. However, due to the difficulties encountered in the beam tests, another type of test specimen was introduced, which was a direct pull-out specimen. In this type of test specimen, lap spliced CFRP rolls have been tested under direct tension, in which the tension has been applied by making use of concrete end blocks that transfer the tension to the rolls. Eleven tests have been made in total. Full material capacity of the rolls could not be achieved due to premature failures. However, important conclusions and recommendations have been made for future studies.
Subject Keywords
Civil engineering.
URI
http://etd.lib.metu.edu.tr/upload/12609694/index.pdf
https://hdl.handle.net/11511/17693
Collections
Graduate School of Natural and Applied Sciences, Thesis
Suggestions
OpenMETU
Core
Inelastic deformation demands on moment-resisting frame structures
Metin, Aslı; Akkar, Sinan D.; Department of Civil Engineering (2006)
Interstory drift ratio is an important parameter for the determination of the structural performance under strong ground motions. A probabilistic procedure is proposed in this study to estimate the inelastic maximum interstory drift ratio. The procedure considers the uncertainties associated with the strong ground motions and structural behavior. Elastic and inelastic response history analyses of reinforced-concrete, moment-resisting frames are used together with a near-fault strong ground motion data set t...
Evaluation of cement mortars by ultrasound
Paksoy, Nesibe Gözde; Yaman, İsmail Özgür; Department of Civil Engineering (2006)
Ultrasonic testing of concrete is often used for the assessment of its uniformity, strength, modulus of elasticity, durability and etc. therefore, the related parameters of testing such as the transducer frequency, the specimen geometry and etc. are well-known. On the other hand, most of the concrete properties are affected by the cement and the mechanical as well as some durability properties of cements are determined through cement mortars. Applications of ultrasound on determining the properties of cemen...
Dynamic characteristics and performance assessment of reinforced concrete structural walls
Kazaz, İlker; Gülkan, Polat; Department of Civil Engineering (2010)
The analytical tools used in displacement based design and assessment procedures require accurate strain limits to define the performance levels. Additionally, recently proposed changes to modeling and acceptance criteria in seismic regulations for both flexure and shear dominated reinforced concrete structural walls proves that a comprehensive study is required for improved limit state definitions and their corresponding values. This is due to limitations in the experimental setups, such that most previous...
Seismic retrofitting of highway bridges in Illinois using friction pendulum seismic isolation bearings and modeling procedures
Dicleli, Murat (Elsevier BV, 2003-07-01)
In this paper, the economical and structural efficiency of friction pendulum bearings (FPB) for retrofitting typical seismically vulnerable bridges in the State of Illinois is studied. For this purpose, a bridge was carefully selected by the Illinois Department of Transportation (IDOT) to represent typical seismically vulnerable bridges commonly used in the State of Illinois. A comprehensive structural model of the bridge was first constructed for seismic analysis. An iterative multi-mode response spectrum ...
Incipient motion of coarse solitary particles
Gülcü, Besim; Göğüş, Mustafa; Department of Civil Engineering (2009)
In this study the incipient motion of coarse solitary particles having different specific weights and shapes was investigated. A tilting flume of rectangular cross-section having a net working length of 12 m was used through the experiments. The slope of the channel and the discharge in the channel are the two basic variable parameters that determine the initiation of motion. Particles made of cement and mixture of cement and iron dust in certain ratios were used in the experiments with an obstructing eleme...
Citation Formats
IEEE
ACM
APA
CHICAGO
MLA
BibTeX
A. Ş. Taşlıgedik, “Lap splice behavior and strength of cfrp rolls,” M.S. - Master of Science, Middle East Technical University, 2008.