Effect of pore size distribution on porosity measurement by computurized tomography

Download
093138.pdf
2000
Demir, Murat
Show full item record
65
views
0
downloads
https://hdl.handle.net/11511/6673
Graduate School of Natural and Applied Sciences, Thesis

Suggestions

Effect of Gas Diffusion Layer Characteristics and Addition of Pore-Forming Agents on the Performance of Polymer Electrolyte Membrane Fuel Cells
Senguel, Erce; Erkan, Serdar; Eroğlu, İnci; BAÇ, NURCAN (Informa UK Limited, 2009-01-01)
The performance of five layer membrane electrode assemblies having different characteristics of gas diffusion layers was determined at 70 degrees C cell temperature and ambient pressure. The maximum power density at 0.6 V was 0.36 W/cm(2) for the membrane electrode assembly prepared with the gas diffusion layer having minimum thickness (SGL BC 30 type). On the other hand, the maximum power density at 0.5 V was 0.44 W/cm(2) for the membrane electrode assembly prepared with SGL BC 34 type gas diffusion layer....
Effect of heating rate on thermoluminescence characteristics of Y2O3 nanoparticles
Hasanlı, Nızamı; Gasanly, N.M. (Elsevier BV, 2019-8)
The present paper reports the results of heating rate dependencies of thermoluminescence (TL) peaks observed for Y2O3 nanoparticles in the below room temperature region. TL glow curve presented six peaks around 62.5, 91.3, 114.5, 162.7, 196.0 and 214.9 K for heating rate of 0.4 K/s. The increase of heating rate resulted in increase in peak maximum temperature and decrease in peak maximum intensity as expected according to theoretical information. Peak maximum temperature-heating rate dependencies of observe...
EFFECT OF SURFACE ROUGHNESS IN PARALLEL-PLATE MICROCHANNELS ON HEAT TRANSFER
Turgay, M. B.; Güvenç Yazıcıoğlu, Almıla (Informa UK Limited, 2009-01-01)
In this study, the effect of surface roughness on convective heat transfer in two-dimensional parallel plate microchannels is analyzed numerically for steady-state, single-phase, developing, and laminar air flow in the slip flow regime. Slip velocity and temperature jump at wall boundaries are imposed to observe the rarefaction effect. The effect of triangular roughness elements on Nusselt number are compared to cases with smooth surfaces. The results indicate that increasing surface roughness reduces heat ...
Effect of layer thickness on the electrical parameters and conduction mechanisms of conjugated polymer-based heterojunction diode
Yildiz, D. E.; APAYDIN, D. H.; Toppare, Levent Kamil; Çırpan, Ali (2017-05-01)
In this study, thickness-dependent current density-voltage (J-V) characteristics obtained for poly{(9,9-dioctylfluorene) 22,7-diyl-(4,7-bis (thien-2-yl)2-dodecyl-benzo[1,2,3] triazole)} (PFTBT) conjugated copolymer based heterojunction diode fabricated on ITO were investigated in terms of electrical characteristics. In order to analyze J-V plots with ITO/PEDOT: PSS/PFTBT: PC61BM/LiF/Al configuration, the thickness-dependent J-V measurements were applied in the thickness range between 90 and 200 nm. The effe...
Effect of solidification rate on spatial distribution of SiC particles in A356 alloy composites
CETIN, Arda; Kalkanlı, Ali (Elsevier BV, 2008-08-26)
The damage and deformation behaviour of particulate reinforced metal matrix composites (PMMCs) can be highly sensitive to local variations in spatial distribution of reinforcement particles, which markedly depend on melt processing and solidification stages during production of PMMCs. The present paper attempts to study the effect of solidification rate on cluster formation in an Al-Si-Mg (A356) alloy composite reinforced with SiC particles and to explore the applicability of spatial functions to PMMC micro...
Citation Formats
M. Demir, “Effect of pore size distribution on porosity measurement by computurized tomography,” Middle East Technical University, 2000.
METU IIS - Integrated Information Service open@metu.edu.tr