Effect of Cooling Rate on Mechanical Properties of MnAlFeNiCoHEAs

2016-02-14
Ulucan, Tolga
Koylan, Serkan
Koc, Seyma
Kalay, Yunus Eren
Show full item record
18
views
0
downloads
https://hdl.handle.net/11511/72331
Unverified, Conference / Seminar

Suggestions

Effect of cooling rate on microstructure and high temperature stability of rapidly solidified Al-Fe-V-Si alloys
Kalkanlı, Ali (Informa UK Limited, 1999-01-01)
Recently, AI-Fe-V-Si alloys have received more attention owing to their high temperature stability associated with vanadium rich precipitates and silicides. In this work, a series of alloys was prepared and processed by melt spinning and gas atomisation to observe the effect of solidification rate on crystal structures existing in both as cast and heat treated conditions. This study covers their microstructural examination and crystallography. The composition of these alloys was Al-(6.8-7.8)Fe-( 1.0-3)V-(1....
Effect of pressure and particle size on the thermal cracking of light crude oils in sandstone matrix
Kök, Mustafa Verşan (Springer Science and Business Media LLC, 2009-4-27)
This research is focused on the effects of pressure (100-300 Pa) and matrix and on light crude oil combustion in sandstone matrix using pressurized differential scanning calorimetry (PDSC). Light crude oils and sandstone mixtures were prepared to give a composition of 15 mass% crude oil in sandstone matrix. A total of forty-eight PDSC experiments were performed. Roger and Morris kinetic model was used to analyse the data obtained from PDSC experiments and the results are discussed.
Effect of particle size and heating rate on the combustion of Silopi asphaltite
Altun, Naci Emre; Kök, Mustafa Verşan (2002-05-01)
In this study, the effects of particle size and heating rate on the combustion properties of Silopi asphaltite were investigated. Nonisothermal thermogravimetry experiments were carried out at three different size fractions and five different heating rates. The TG/DTG experiments were carried out from ambient to 900 degreesC in air. The data obtained were analyzed for the determination of the combustion characteristics of the sample. Also an Arrhenius type kinetic model complemented with the weighed mean ac...
Effect of heating rate on thermoluminescence characteristics of Y2O3 nanoparticles
Hasanlı, Nızamı; Gasanly, N.M. (Elsevier BV, 2019-8)
The present paper reports the results of heating rate dependencies of thermoluminescence (TL) peaks observed for Y2O3 nanoparticles in the below room temperature region. TL glow curve presented six peaks around 62.5, 91.3, 114.5, 162.7, 196.0 and 214.9 K for heating rate of 0.4 K/s. The increase of heating rate resulted in increase in peak maximum temperature and decrease in peak maximum intensity as expected according to theoretical information. Peak maximum temperature-heating rate dependencies of observe...
Effect of synthesis environment on the electrochemical properties of (FeMnCrCoZn)(3)O-4 high-entropy oxides for Li-ion batteries
Bayraktar, Deniz Okan; LÖKÇÜ, ERSU; Özgür, Çağla; Erdil, Tuncay; Toparlı, Çiğdem (2022-09-01)
High-entropy oxides (HEOs) have gained significant attention from lithium-ion batteries since they can present cycling stability and possess a high specific capacity. While many studies have focused on discovering new high entropy oxides by changing their components, the influence of the synthesis environment on the structural properties and thus electrochemical behavior remain unresolved. Herein, we studied the effect of the synthesis environment, which is argon and air on the structural and electrochemica...
Citation Formats
T. Ulucan, S. Koylan, S. Koc, and Y. E. Kalay, “Effect of Cooling Rate on Mechanical Properties of MnAlFeNiCoHEAs,” 2016, Accessed: 00, 2021. [Online]. Available: https://hdl.handle.net/11511/72331.
METU IIS - Integrated Information Service open@metu.edu.tr