Investigating the influence of quenching conditions, diameter and material inhomogenity on distortion of steel shafts

2009-01-01
Şimşir, Caner
Lübben, T
Gür, Cemil Hakan
Show full item record
52
views
0
downloads
https://hdl.handle.net/11511/77500
European Congress on Advanced Materials (EUROMAT), ( 01 Ocak 2009)
Unverified, Conference / Seminar

Suggestions

Investigating the Effects of Conventional and Non-Conventional Welding Techniques on Microstructure and Residual Stress in Creep-Resistant Steels
Gür, Cemil Hakan; Tirkeş, Süha(2018-12-31)
The use of creep-resistant steels for the fabrication of components in boiler tubes and fittings in power plants due to their high temperature strength properties has increased in recent years. However, experience with the welded creep resistant steel components currently in service as well as the results of creep tests indicate reduced creep rupture strength of weldments compared to the base material. Besides, it is known that the magnitude and distribution of a residual stress play a vital role in the int...
Investigating the effect of number of weld passes on the residual stress state of steel plates by micro magnetic method
Erian, Gökhan; Batıgün, Caner; Çam, İbrahim; Gür, Cemil Hakan (null; 2012-09-17)
Variations of surface residual stresses with subsequent weld passes were investigated in the API 5L X70 steel plates by Magnetic Barkhausen Noise (MBN) method. The plates were welded by applying different number of passes under fully clamped condition. After each weld pass, MBN signal and hardness distributions on the front and back surfaces of the plates were measured. A specific calibration procedure and set-up was used for conversion of MBN signals into elastic stress values. The results were analyzed by...
Investigating the effects of quenching and tempering on steel microstructures by Magnetic Barkhausen Noise method
Gür, Cemil Hakan; Çam, İbrahim (2012-12-01)
Non-destructive evaluation of the properties of the heat treated steels is a challenging task. In this study, quenched and quenched-tempered (200°C and 600°C) SAE 1040 and SAE 4140 steels were characterized by Magnetic Barkhausen Noise (MBN) method. First, the microstructures of the samples were characterized by SEM examination and hardness measurements. Then, the MBN signals were evaluated by using a commercial Barkhausen noise system. The results showed that the MBN response of the as-quenched martensite ...
Investigating the effect of solids retention time on pesticides removal in an activated sludge process
Kocaman, Kumru; Yetiş, Ülkü; Dilek, Filiz Bengü (2022-10-01)
© 2022 Elsevier B.V.The levels of pesticides reaching the biological wastewater treatment plants have been increasing. Operational conditions leading to the most efficient removal of pesticides in these plants should be evaluated first before attempting tertiary-level treatment options. This study investigated the influence of solids retention times (SRTs) on the removal of three pesticides (carbendazim, imidacloprid, and aclonifen) in the activated sludge process. Laboratory-scale reactors receiving these ...
Investigating the correlation between magnetic Barkhausen noise emission and the fatigue life of shot-peened AISI 4140 steel
Çalışkan, S.; Gür, Cemil Hakan (British Institute of Non-Destructive Testing (BINDT), 2019-01-01)
The performance of engineering components under conditions of fatigue can be improved by shot peening. The location and magnitude of the highest residual compressive stress, the depth of the compression zone and the stability of the residual stress state during cyclic loading are critical parameters for maximum utilisation of the advantageous influence of shot peening on fatigue performance. For accurate assessment of fatigue lifetime, residual stresses should be considered because they are algebraically su...
Citation Formats
C. Şimşir, T. Lübben, and C. H. Gür, “Investigating the influence of quenching conditions, diameter and material inhomogenity on distortion of steel shafts,” presented at the European Congress on Advanced Materials (EUROMAT), ( 01 Ocak 2009), Glasgow, İngiltere, 2009, Accessed: 00, 2021. [Online]. Available: https://hdl.handle.net/11511/77500.
METU IIS - Integrated Information Service open@metu.edu.tr