Determination of conversion factors of UCS from point load test for evaporites and sedimentary rocks and numerical modelling

2016-07-29
Öztürk, Hasan
Show full item record
62
views
0
downloads
https://hdl.handle.net/11511/73980
Global Conference on Applied Computing in Science and Engineering (2016)
Department of Mining Engineering, Conference / Seminar

Suggestions

Determination of the 1st buckling and collapse loads for integrally stiffened panels by artificial neural network and design of experiment methodology
Güzel, Şükran Gizem; Gürses, Ercan (2021-01-22)
Buckling is a structural instability that load carrying capacity of a structural element may suddenly decrease. This sudden change in the load carrying capacity may cause catastrophic failures. Therefore, determination of the first buckling and collapse loads of structural elements is essential. FE analyses and structural testing are used to determine buckling characteristics of a structural element. However, in early design stages, FE analyses are time consuming and structural testing is costly. In this pa...
Determination of residual stress state in SAE/AISI 8620 carburized steel by non-destructive testing methods
Kaleli, Tuğçe; Gür, Cemil Hakan; Department of Metallurgical and Materials Engineering (2017)
Industrial performance of the carburized steels is mainly dependent on the residual stress state in the carburized layer that is controlled by the process parameters such as carburizing temperature and time. Non-destructive evaluation of the material properties and residual stress state has been gained importance for industrial applications due to its advantages such as measurement speed and complete control possibility of the components by automation. The aim of this thesis is to investigate the efficiency...
Determination of Displacement Amplification Factors for Chevron BRBFs
Bozkurt, Mehmet Bakır; Özkılıç, Yasin Onuralp; Topkaya, Cem (null; 2017-10-05)
Buckling restrained braced frames (BRBFs) can be used as a lateral load resisting system in high seismic regions. In the United States it is necessary to comply with the requirements defined in the Seismic Provisions for Structural Steel Buildings (AISC341- 10) for the design and production of BRBs. In addition, response factors defined in Minimum Design Loads for Buildings and Other Structures (ASCE 7-10) should be utilized. In this study, deflection amplification factor (Cd) is evaluated. Pursuant to this...
Determination of ion dose and profiles in Ge-74 and Sn-120 implanted silicon layers by PIXE, NAA, RBS and SIMS
Belin, B; Bode, P; Turan, Raşit; Van Meerten, TG (2004-01-01)
Implanted Ge-74 and Sn-121 concentrations in silicon (Si) layers were investigated by particle induced X-ray emission (PIXE), instrumental neutron activation analysis (INAA), Rutherford backscattering spectrometry (RBS) and secondary ion mass spectrometry (SIMS). Slight differences were observed in the results obtained. It was shown that PIXE and INAA are as powerful as the traditional RBS and SIMS spectroscopy for the investigation of thin layered Si.
Determination of tool point FRF of micro tools under operational conditions using analytical methods
Özşahin, Orkun (Journal of the Faculty of Engineering and Architecture of Gazi University, 2018-01-01)
Tool point Frequency Response Function (FRF) for micro tools cannot be measured using impact testing and modal analysis. In addition, micro machining operations are performed at high spindle speeds and due to the gyroscopic moments and centrifugal forces tool point FRF changes during machining operations. In this study, micro tools are modeled analytically including the fluted geometry of the tool and operational effects. Moreover, for the machining centers where spindle geometry is unknown, a new coupling ...
Citation Formats
H. Öztürk, “Determination of conversion factors of UCS from point load test for evaporites and sedimentary rocks and numerical modelling,” presented at the Global Conference on Applied Computing in Science and Engineering (2016), Varna, Bulgaristan, 2016, Accessed: 00, 2021. [Online]. Available: https://hdl.handle.net/11511/73980.
METU IIS - Integrated Information Service open@metu.edu.tr