Investigation of Air Core Characteristics of a Pressure Swirl Injector Using Two Different Volume of Fluid Methods

Date

2019-09-20

Author

Öztürkmen, Musa Onur
Özyörük, Yusuf

Metadata

Show full item record

Item Usage Stats

123
views

0
downloads

URI

https://hdl.handle.net/11511/85079

Conference Name

ECCOMAS MSF 2019 4th International Conference on Multi-Scale Computational Methods for Solids and Fluids, Bosnia-Herzegovina, (18 - 20 Eylül 2019)

Collections

Department of Aerospace Engineering, Conference / Seminar

Suggestions

OpenMETU
Core

Investigation of flow around a bridge abutment in a flat bed channel using Large Eddy Simulation Köken, Mete (2007-12-01) Large Eddy Simulation (LES) is used to numerically investigate the horseshoe vortex (HV) system around a vertical bridge abutment located on a flat bed in a straight channel with vertical lateral walls corresponding to conditions at the initiation of the scour process. The simulation is performed with upstream fully turbulent flow including the turbulent fluctuations obtained from a precalculated LES simulation. The dynamics of the instantaneous coherent structures associated with the HV system around the b...
Investigation of flowfield characteristics due to shock wave-boundary layer interaction on compression decompression corners using les Karpuzcu, Irmak Taylan; Sert, Cüneyt; Department of Mechanical Engineering (2019) Shock wave boundary layer interactions occur in industrial flows where the flow is transonic, supersonic or hypersonic and there is an incoming boundary layer present. Many of the air crafts such as planes, rockets, missiles, re-entry vehicles, and supersonic wind tunnels experience shock wave boundary layer interactions. These interactions can take place on an air craft at several different places such as the air intakes, ramps, forebody and fins, and also the diffuser section of a supersonic wind tunnel. ...
Investigation of fatigue behavior of a high strength lower bainitic structure in 60SIMN5 steel via a modified testing method Uluğ, Emirhan; Ögel, Bilgehan; Department of Metallurgical and Materials Engineering (2019) A steel with high silicon content can yield carbide-free bainite after an isothermal bainitic transformation. In this thesis study, fatigue behavior of a high strength carbide-free lower bainitic structure, which was produced from 60SiMn5 steel, was investigated. The fatigue tests of the same steel with tempered martensitic microstructure were also carried out for comparison purposes. Before fatigue testing, the mechanical properties of the specimens were also determined, which include hardness, yield stren...
Investigation of unsteady wake-separated boundary layer interaction using particle-image-velocimetry Uzol, Oğuz; Cranstone, Alex; Hodson, Howard (2007-05-17) The current paper presents an experimental investigation of the interaction between unsteady wakes and the separated boundary layer on the suction side of an ultra-high-lift low-pressure turbine airfoil. Two-dimensional Particle Image Velocimetry (PIV) measurements of the unsteady boundary layer over the T106C LP turbine profile were performed in a low speed linear cascade facility, at selected phases of passing wakes. The wakes are created by moving cylindrical bars across the inlet of the test section. V...
Investigation of Moisture Dissipation in Foam-Based Warm Mix Asphalt Using Synchrotron-Based X-Ray Microtomography Kutay, M. Emin; Öztürk, Hande Işık (American Society of Civil Engineers (ASCE), 2012-06-04) Foam-based Warm Mix Asphalt (WMA) technologies decrease the viscosity of the asphalt so that it is workable during construction. However, after construction, viscosity increases rapidly as the foam disappears and temperature drops. During the process of dissipation of foam, depending on the environmental conditions, the moisture may not escape and may be trapped inside the mixture. This trapped moisture can cause detrimental failures by breaking the adhesive bonds between the aggregates and the asphalt bind...

Citation Formats

M. O. Öztürkmen and Y. Özyörük, “Investigation of Air Core Characteristics of a Pressure Swirl Injector Using Two Different Volume of Fluid Methods,” presented at the ECCOMAS MSF 2019 4th International Conference on Multi-Scale Computational Methods for Solids and Fluids, Bosnia-Herzegovina, (18 - 20 Eylül 2019), 2019, Accessed: 00, 2021. [Online]. Available: https://hdl.handle.net/11511/85079.