Characterization of phase properties and deformation in ferritic-austenitic duplex stainless steels by nanoindentation and finite element method

Date

2017-01-01

Author

Schwarm, Samuel C.
Kolli, R. Prakash
Aydoğan Güngör, Eda
Mburu, Sarah
Ankem, Sreeramamurthy

Metadata

Show full item record

This work is licensed under a Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.

Item Usage Stats

25
views

0
downloads

The phase properties and deformation behavior of the delta-ferrite and gamma-austenite phases of CF-3 and CF-8 cast duplex stainless steels were characterized by nanoindentation and microstructure-based finite element method (FEM) models. The elastic modulus of each phase was evaluated and the results indicate that the mean elastic modulus of the delta-ferrite phase is greater than that of the gamma-austenite phase, and the mean nanoindentation hardness values of each phase are approximately the same. The elastic FEM model results illustrate that greater von Mises stresses are located within the delta-ferrite phase, while greater von Mises strains are located in the gamma-austenite phase in response to elastic deformation. The elastic moduli calculated by FEM agree closely with those measured by tensile testing. The plastically deformed specimens exhibit an increase in misorientation, deformed grains, and subgrain structure formation as measured by electron backscatter diffraction (EBSD).

URI

https://hdl.handle.net/11511/69903

Journal

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

DOI

https://doi.org/10.1016/j.msea.2016.10.116

Collections

Department of Metallurgical and Materials Engineering, Article

Suggestions

OpenMETU
Core

Preparation and Characterization of Low Density Polyethylene/Ethylene Methyl Acrylate Glycidyl Methacrylate/Organoclay Nanocomposites Coskunses, Fatma Isik; Yılmazer, Ülkü (Wiley, 2011-06-05) The effects of organoclay type, compatibilizer, and the addition order of components during melt-blending process on the morphology and thermal, mechanical, and flow properties of ternary nanocomposites based on low-density polyethylene (LDPE) were investigated. As a compatibilizer, ethylene/methyl acrylate/glycidyl methacrylate (E-MA-GMA), as organoclays Cloisites (R) 15A, 25A, and 30B were used. All samples were prepared by a corotating twin screw extruder, followed by injection molding. The highest incre...
Effect of impact modifier on the properties of poly (ethylene terephthalate)-organoclay nanocomposites Yılmazer, Ülkü; Alyamac, Elif (2006-11-30) The effects of component concentrations and addition order of the components, on the final properties of ternary nanocomposites composed of amorphous poly (ethylene terephthalate) matrix, organically modified clay, and an ethylene / methyl acrylate / glycidyl methacrylate (E-MAGMA) terpolymer were studied. All formulations were prepared by melt compounding of the components with a two-step mixing procedure in a corotating twin-screw extruder. Considering the X-Ray Diffraction, SEM, impact and strain at brea...
CHARACTERIZATION OF SILICA CATALYST SUPPORTS BY SINGLE AND MULTIPLE-QUANTUM PROTON NMR-SPECTROSCOPY HWANG, SJ; Üner, Deniz; KING, TS; PRUSKI, M; GERSTEIN, BC (American Chemical Society (ACS), 1995-03-16) Cab-O-Sil HS5, used as the support in silica supported ruthenium (Ru/SiO2) catalysts, was characterized via single and multiple quantum (MQ) H-1 NMR spectroscopy. The samples were studied both in the presence and in the absence of ruthenium. Single quantum spin counting of protons on silica support with and without ruthenium metal indicated that the total number of hydroxyl groups decreased significantly with increasing reduction temperature over the range of 350-530 degrees C. Two different components show...
Characterization of conducting copolymer of thiophene via pyrolysis mass spectrometry Levent, Anil; Hacaloğlu, Jale; Toppare, Levent Kamil (2005-12-01) In this work, structural and thermal characterization of a conducting copolymer of thiophene (PTh) with 2-methylbutyl-2-(3-thienyl)acetate prepared by two different methods has been performed by pyrolysis mass spectrometry techniques. The pyrolysis mass spectrometry data of both components of the copolymer, polythiophene, PTh, poly(2-methylbutyl-2-(3-thienyl)acetate), PMBTA and PTh/PMBTA have been analyzed and compared. It has been determined that when the electrochemical polymerization of thiophene was ach...
Preparation of silica coated cobalt ferrite magnetic nanoparticles for the purification of histidine-tagged proteins Aygar, Gulfem; Kaya, Murat; Özkan, Necati; Kocabıyık, Semra; Volkan, Mürvet (2015-12-01) Surface modified cobalt ferrite (CoFe2O4) nanoparticles containing Ni-NTA affinity group were synthesized and used for the separation of histidine tag proteins from the complex matrices through the use of imidazole side chains of histidine molecules. Firstly, CoFe2O4 nanoparticles with a narrow size distribution were prepared in an aqueous solution using the controlled co-precipitation method. In order to obtain small CoFe2O4 agglomerates, oleic acid and sodium chloride were used as dispersants. The CoFe2O4...

Citation Formats

S. C. Schwarm, R. P. Kolli, E. Aydoğan Güngör, S. Mburu, and S. Ankem, “Characterization of phase properties and deformation in ferritic-austenitic duplex stainless steels by nanoindentation and finite element method,” MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, pp. 359–367, 2017, Accessed: 00, 2021. [Online]. Available: https://hdl.handle.net/11511/69903.