Effect of Alloying Elements on Diffusing Bonding Parameters in Al6063

Date

2017-03-02

Author

Atabay, Sila Ece
Dericioğlu, Arcan Fehmi

Metadata

Show full item record

Item Usage Stats

49
views

0
downloads

URI

http://www.programmaster.org/PM/PM.nsf/ViewSessionSheets?OpenAgentParentUNID=BADADC0FEF3860D385257FDE001F12DD
https://hdl.handle.net/11511/82616

Collections

Unverified, Conference / Seminar

Suggestions

OpenMETU
Core

Effect of Alloying Element Additions on Order-Disorder Phase Transformation Temperatures in Fe-Al-X Intermetallics Yıldırım, Mehmet; Mekhrabov, Amdulla; Akdeniz, Mahmut Vedat (null; 2008-10-16)
Effect of crystal orientation on the segregation of aliovalent dopants at the surface of La0.6Sr0.4CoO3 Pişkin, Fatih; Bliem, Roland; Yildiz, Bilge (2018-08-07) The effect of crystal orientation on aliovalent dopant segregation at the surface of La0.6Sr0.4CoO3 as a model perovskite oxide was investigated. La0.6Sr0.4CoO3 pellets were produced and then annealed in air at 800 degrees C for 2-5 hours to drive the cation segregation at the surface. To quantify the chemical state of the pellets' surface, including cation composition and secondary phase precipitates rich in Sr, the pellets were characterized by X-ray photoelectron spectroscopy and Auger electron spectrosc...
Effect of processing parameters on humidity sensing behavior of MgAl2O4 spinel ceramics Cambaz, Zarife Göknur; Timuçin, Muharrem; Department of Metallurgical and Materials Engineering (2003) An experimental study has been conducted in order to determine the effects of processing parameters on the humidity sensing characteristics of ceramic sensors produced from magnesium aluminate. MgAİ2Û4 powders were synthesized by the mixed oxide technique and by the citrate route in the laboratory. In some experiments, the powders were doped with Na+, Mn2+, or Ti4+ ions in order to modify the sintering and the response behavior of the spinel ceramics. The variations in electrical impedance were determined a...
Effect of Welding Parameters on the Liquation Cracking Behavior of High-Chromium Ni-Based Superalloy Mashhuriazar, Amirhossein; Omidvar, Hamid; Gür, Cemil Hakan; Sajuri, Zainuddin (2020-11-01) Gas turbine blades working under extremely harsh operating conditions are made of superalloys. These superalloys are exposed to various damage mechanisms, which wear them out gradually. Welding is often preferred to repair the damaged components for cost minimization. This study aimed to investigate the effects of flexural load, heat input, and welding speed on the weldability and intergranular liquation cracking of high-chromium Ni-based superalloy. For this purpose, a series of Sigmajig tests designed bas...
Effect of grain size and porosity on phonon scattering enhancement of Ca3Co4O9 Gunes, Murat; Özenbaş, Ahmet Macit (2015-03-25) Ca3Co4O9 (C-349) samples with average grain sizes ranging from 18 nm to 2 mu m were synthesized using the citrate sol-gel method. PEG 400 was used to vary the particle size and porosity, and the thermoelectric (TE) properties were examined from 300 to 1000 K. Nanostructuring and porosity do not appear to significantly affect the Seebeck coefficient; however, a considerable increase in the resistivity over the entire temperature range was observed, leading to lower power factors for the nano-sized samples. T...

Citation Formats

S. E. Atabay and A. F. Dericioğlu, “Effect of Alloying Elements on Diffusing Bonding Parameters in Al6063,” 2017, Accessed: 00, 2021. [Online]. Available: http://www.programmaster.org/PM/PM.nsf/ViewSessionSheets?OpenAgentParentUNID=BADADC0FEF3860D385257FDE001F12DD.