Collection of Metal Powders From Recycled Hard Particle Embedded Composite Cutting Tools

2018-10-27
Altunbaşak, Tansu
Kul, Mehmet
Karakaya, İshak
Diamond particles embedded cutting sockets which are placed on the circumference of the metal disc in industry to cut hard materials are discarded after completing their economic life. However, large quantities of metals and diamond particles remain in the discarded sockets. An electrochemical recycling procedure to form metal powders and gain diamond particles comprehensively and efficiently have been studied. The effects of temperature, acid concentration, copper ion concentration of the electrolyte and current density were studied. Collected metallic powders were characterized by X-Ray diffraction (XRD), scanning electron microscopy (SEM) and single point Brunauer, Emmett and Teller (BET) analysis. Results show how to optimize the process parameters to obtain compact and dense metallic powders.
19th International Metallurgy and Materials Congress (IMMC 2018), (25 - 27 Ekim 2018)

Suggestions

Analysis of warm forging process
Aktakka, Gülgün; Darendeliler, Haluk; Department of Mechanical Engineering (2006)
Forging is a metal forming process commonly used in industry. Forging process is strongly affected by the process temperature. In hot forging process, a wide range of materials can be used and even complex geometries can be formed. However in cold forging, only low carbon steels as ferrous material with simple geometries can be forged and high capacity forging machinery is required. Warm forging compromise the advantages and disadvantages of hot and cold forging processes. In warm forging process, a product...
Complete Recycling of Waste Diamond Cutting Tools by an Electrochemical Method
Altunbaşak, Tansu; Kul, Mehmet; Karakaya, İshak (2018-03-15)
Diamond and other valuable particle embedded composite cutting tools can be produced by different techniques according to its area of utilization. Co, Ni, Ti and W metals are used as binder while Cu, Sn, brass and bronze used as filler in the manufacturing above mentioned cutting tools. About 20 % of composite cutting tools are not consumed when they are discarded. Current recycling processes contribute recovery of diamond and abrasive parts by filtration, after acid dissolution. Besides diamond, metallic c...
Complete Recycling of Waste Diamond Cutting Tools by an Electrochemical Method
Altunbaşak, Tansu; Kul, Mehmet; Karakaya, İshak (2018-03-15)
Diamond and other valuable particle embedded composite cutting tools can be produced by different techniques according to its area of utilization. Co, Ni, Ti and W metals are used as binder while Cu, Sn, brass and bronze used as filler in the manufacturing above mentioned cutting tools. About 20 % of composite cutting tools are not consumed when they are discarded. Current recycling processes contribute recovery of diamond and abrasive parts by filtration, after acid dissolution. Besides diamond, metallic c...
Investigation of the effects of equal channel angular extrusion on light weight alloys
Karpuz, Pınar; Gür, Cemil Hakan; Karaman, İbrahim; Department of Metallurgical and Materials Engineering (2012)
Severe plastic deformation methods are of great interest in industrial forming applications, as they give rise to significant refinement in microstructures and improvements in mechanical and physical properties. In the “Equal Channel Angular Extrusion (ECAE)”, which is the most common method for production of ultrafine grained bulk samples, very high plastic strains are introduced into the bulk material without any change in cross section. This study is composed of two main parts. Part I focuses on the plas...
Characterization of ultra-fine grained steel samples produced by high pressure torsion via magnetic barkhausen noise analysis
Bayramoğlu, Sadık; Gür, Cemil Hakan; Department of Metallurgical and Materials Engineering (2009)
High Pressure Torsion (HPT) is one of the most widely used severe plastic deformation methods which enable to obtain a crack free ultra-fine grained bulk material with improved mechanical properties like increased strength and toughness. In the process, a disc shaped sample is pressed between two anvils and deformed via surface friction forces by rotating one of the anvils. The aim of this study is to nondestructively characterize the variations in the deformation uniformity of the severely deformed steel d...
Citation Formats
T. Altunbaşak, M. Kul, and İ. Karakaya, “Collection of Metal Powders From Recycled Hard Particle Embedded Composite Cutting Tools,” İstanbul, Türkiye, 2018, p. 692, Accessed: 00, 2021. [Online]. Available: http://www1.metalurji.org.tr/immc2018/bildiriler_kitabi.pdf.