Microstructural and mechanical characterization of metal active gas welded joint between cast iron and low carbon steel

Download
2011
Ertürk, Murat Tolga
This study focuses on joining pearlitic ductile cast iron with low carbon steel by welding and investigation of this joint in microstructural and mechanical viewpoints. For this purpose E355 steel and GJS600-3 cast iron were joined using metal active gas (MAG) welding process by G3Si1 filler wire. The joining process is shaped mainly by the problems related to the low weldability of cast. Preheating was applied to prevent formation of cooling cracks and effects of post weld heat treatments (PWHT) were surveyed. Micro examination and micro hardness tests were applied to characterize the general microstructure. Grain size measurements were done for E355. Hardness profiles, tension and impact toughness properties were designated via mechanical tests. Fatigue behavior was surveyed and general fracture characteristics were determined via scanning electron microscopy (SEM) examinations. According to study it was concluded that successful weld joint could be formed between the materials by suitable preheating. Formation of ledeburitic white cast iron and martensite in heat affected zone of cast piece was witnessed. It was possible to lower high hardness values of these phases gradually by increasing post weld heat treatment temperatures. The weld joint behaved superior to the base metals under tension and fatigue tests. In tension tests failure occurred at E355 base metal whereas fatigue loading resulted failure at GJS600-3. A great impact toughness variation was determined between two pieces. It is seen that heat treatments had minor effect on mechanical test results except hardness. The study was concluded that a useful fusion weld joint between these materials can be built.

Suggestions

Characterization of steel microstructures by magnetic barekhausen noise technique
Davut, Kemal; Gür, Cemil Hakan; Department of Metallurgical and Materials Engineering (2006)
This aim of this thesis is to examine the possibility of using Magnetic Barkhausen Noise (MBN) technique in characterizing the microstructures of quenched and tempered low alloy steels as well as annealed low carbon steels. To determine the average grain size by MBN, SAE 1010 steel consisting of dominantly ferrite was used. The specimens were slowly cooled in the furnace after austenitizing at different time and temperature variations. By metallographic examination the average ferrite grain size of specimen...
Microstructural characterization of hypoeutectoid steels quenched from the Ae1 - Ae3 intercritical temperature range by magnetic barkhausen noise technique
Boyacıoğlu, Beril; Gür, Cemil Hakan; Department of Metallurgical and Materials Engineering (2006)
This thesis aims to examine the possibility of using Magnetic Barkhausen Noise technique in characterizing the ferritic-martensitic microstructure of hypoeutectoid steels quenched from the intercritical temperature range. For this purpose, rectangular specimens were prepared from SAE 1020, 1040 and 1060 steels. The specimens were heated at different temperatures within the intercritical temperature range and then quenched into water. Microstructures of the specimens were characterized by metallographic exam...
The effect of austempering parameters on impact and fracture toughness of din 35nicrmov12.5 gun barrel steel
Aksu, Engin; Atala, Haluk; Department of Metallurgical and Materials Engineering (2005)
In this study the effects of different austempering times and temperatures on impact toughness, hardness and fracture toughness properties of 35NiCrMoV12.5 gun barrel steel are investigated. 300 °C, 325 °C and 350 °C were chosen as austempering temperatures. Isothermal holding times at these temperatures were chosen as 1 minute, 10 minutes, 1 hour and 10 hours. It was found that, 350 °C being an exception, austempering temperature and impact toughness has an inverse relationship and impact toughness increas...
Aluminum Oxide and Titanium Diboride Reinforced Metal Matrix Composite and Its Mechanical Properties
Kurtoğlu, Aziz; Sevinç, Naci; Department of Metallurgical and Materials Engineering (2004)
This study is on the production and testing of an aluminum metal matrix composite. Metal Matrix Composites can be produced in several different ways. In this study, an aluminum matrix composite is produced by direct addition of the reinforcement ceramic into the liquid metal. The ceramic reinforcement for this process was a mixture of TiB2 and Al2O3 which was produced by means of a thermite reaction of reactants Al, B2O3 and TiO2 all in powder form with their respective stoichiometric amounts. This ceramic ...
Determination of susceptibility to intergranular corrosion in AISI 304L and 316L type stainless steels by electrochemical reactivation method
Aydoğdu, Gülgün Hamide; Aydınol, Mehmet Kadri; Department of Metallurgical and Materials Engineering (2004)
Austenitic stainless steels have a major problem during solution annealing or welding in the temperature range of 500-800 °C due to the formation of chromium carbide, which causes chromium depleted areas along grain boundaries. This means that the structure has become sensitized to intergranular corrosion. Susceptibility to intergranular corrosion can be determined by means of destructive acid tests or by nondestructive electrochemical potentiokinetic reactivation (EPR) tests. The EPR test, which provides q...
Citation Formats
M. T. Ertürk, “Microstructural and mechanical characterization of metal active gas welded joint between cast iron and low carbon steel,” M.S. - Master of Science, Middle East Technical University, 2011.