Water-borne and air-drying oil-based resins

Date

2004-04-01

Author

Gündüz, Güngör
Khalid, AH
Mecidoglu, IA
Aras, L

Metadata

Show full item record

This work is licensed under a Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.

Item Usage Stats

205
views

0
downloads

New water-borne polyurethane resins were produced using maleinized monoglyceride (MMG), hydroxyl-terminated polybutadiene (HTPB), toluene di-isocyanate, and ethylene diamine (EDA). Maleinization was performed in order to insert hydrophilic groups in the fatty acid residues, which were then inserted to the backbone of polyurethane. The MMG was mixed with HTPB in different proportions, and the mixture was used as the polyol part of water-borne polyurethane resin. It was then reacted with toluene di-isocyanate, and the isocyanate end groups were blocked with methyl ethyl ketoxime (MEKO). The ratio of MMG to total polyol was changed between 40 and 70 mol%, while the [NCO]/[OH] ratio was kept at 1.5 in all samples. The carboxylic acid groups of MMG were then neutralized with triethyl amine. The formation of ionic groups imparts water dispersibility. Chain extension was performed by adding EDA and baking at 125 degreesC. Hardness, adhesion, impact resistance, bending, and abrasion resistance tests were applied to the specimens. The samples exhibited good physical and mechanical properties.

Subject Keywords

Organic Chemistry, Materials Chemistry, General Chemical Engineering, Surfaces, Coatings and Films

URI

https://hdl.handle.net/11511/56770

Journal

PROGRESS IN ORGANIC COATINGS

DOI

https://doi.org/10.1016/j.porgcoat.2003.09.021

Collections

Department of Chemical Engineering, Article

Suggestions

OpenMETU
Core

PREPARATION AND CHARACTERIZATION OF PERLITE-FILLED HIGH-DENSITY POLYETHYLENES .1. MECHANICAL-PROPERTIES AKINOKTEM, G; TINCER, T (Wiley, 1994-11-21) Four different types of high-density polyethylenes (HDPE) were blended with perlite at different concentrations. Silane coupling agent gamma-aminopropyltriethoxy silane (gamma-APS, A-1100) was used to enhance the adhesion between perlite and HDPEs. Ultimate tensile strength and elastic modulus increased as the perlite content increased, while ultimate elongations decreased with the increasing amount of perlite. Exceptional variations in the measured properties are explained in terms of the differences in po...
Structural, electrochemical and optical comparisons of tungsten oxide coatings derived from tungsten powder-based sols Isik, Dilek; AK, METİN; Durucan, Caner (Elsevier BV, 2009-11-02) Tungsten trioxide (WO3) electrochromic coatings have been formed on indium tin oxide-coated glass substrates by aqueous routes. Coating sols are obtained by dissolving tungsten powder in acetylated (APTA) or plain peroxotungstic acid (PTA) solutions. The structural evolution and electrochromic performance of the coatings as a function of calcination temperature (250 degrees C and 400 degrees C) have been reported. Differential scanning calorimetry and X-ray diffraction have shown that amorphous WO3 films ar...
Characterization and Electrical Conductivity of Poly(ethylene glycol)/Polyacrylonitrile/Multiwalled Carbon Nanotube Composites Aqeel, Salem M.; Kucukyavuz, Zuhal (Wiley, 2011-01-05) Polymer blends based on poly(ethylene glycol), polyacrylonitrile, and multiwalled carbon nanotubes (MWNTs) were prepared by the solvent cast technique from the dispersion of the MWNTs in the concentration range 0-3.45 wt %. The interaction of the MWNTs with the polymer blend was confirmed by a Fourier transform infrared (FTIR) spectroscopy study. The thermal properties of the polymer blend with the MWNTs were carried out by means of differential scanning calorimetry (DSC). It was evident from DSC that the p...
Green to highly transmissive switching multicolored electrochromes: Ferrocene pendant group effect on electrochromic properties Ozdemir, Serife; BALAN, Abidin; BARAN, Derya; Doğan, Özdemir; Toppare, Levent Kamil (Elsevier BV, 2011-02-01) Two new quinoxaline and ethylenedioxythiophene (EDOT) based polymers: poly(5,8-bis(2,3-dihydrothieno[3,4-b][1,4]dioxin-5-yl)-2-(phenyll)-3-ferrocenylquinoxaline) (P1) and poly(5,8-bis(2,3-dihydrothieno[3,4-b][1,4]dioxin-5-yl)-2,3-di(naphthalen-2-yl) quinoxaline) (P2) were synthesized and characterized in terms of their electrochemical and spectroelectrochemical properties. The polymers were both p and n-type dopable. The polymers can be switched between green and transparent states during p-doping/dedoping....
Modification of glassy carbon electrode by the electrochemical oxidation of 3-aminophenylcalix[4]pyrrole in nonaqueous media TANER, BİLGE; DEVECİ, PERVİN; ÜSTÜNDAĞ, ZAFER; Keskin, Selda; ÖZCAN, EMİNE; SOLAK, ALİ OSMAN (Wiley, 2012-02-01) 3-Aminophenylcalix[4]pyrrole (3APCP) was grafted to a glassy carbon (GC) surface during the electrochemical oxidation process in 0.1 M tetrabutylammoniumtetra-fluoroborate (TBATFB) containing acetonitrile solution. The presence of a surface film was confirmed electrochemically by comparing voltammograms of dopamine and ferricyanide redox probes at the bare and modified electrodes. Reflection-absorption infrared spectroscopy (RAIRS), XPS, atomic force microscopy (AFM), ellipsometry and the contact angle meas...

Citation Formats

G. Gündüz, A. Khalid, I. Mecidoglu, and L. Aras, “Water-borne and air-drying oil-based resins,” PROGRESS IN ORGANIC COATINGS, pp. 259–269, 2004, Accessed: 00, 2020. [Online]. Available: https://hdl.handle.net/11511/56770.