Comparative study of yield-power law drilling fluids flowing through annulus

2007-01-01
Ozbayoglu, M. E.
Omurlu, C.
An exact solution for calculating the frictional pressure losses of yield-power law (YPL) fluids flowing through concentric annulus is proposed. A solution methodology is presented for determining the friction factor for laminar and nonlaminar flow regimes. The performance of the proposed model is compared to widely used models as well as the experimental results of 10 different mud samples obtained from the literature. The results showed that the proposed model could estimate the frictional pressure losses with an error of less than 10% in most cases for both laminar and nonlaminar flow regimes, more accurately than the widely used models available in the literature.
PETROLEUM SCIENCE AND TECHNOLOGY

Suggestions

A Mechanistic Model for Predicting Frictional Pressure Losses for Newtonian Fluids in Concentric Annulus
SORGUN, MEHMET; Ozbayoglu, M. E. (Informa UK Limited, 2010-01-01)
A mathematical model is introduced estimating the frictional pressure losses of Newtonian fluids flowing through a concentric annulus. A computer code is developed for the proposed model. Also, extensive experiments with water have been conducted at Middle East Technical University, Petroleum and Natural Gas Engineering Department Flow Loop and recorded pressure drop within the test section for various flow rates. The performance of the proposed model is compared with computational fluid dynamics (CFD) soft...
Sensitivity Analysis of Major Drilling Parameters on Cuttings Transport during Drilling Highly-inclined Wells
Ozbayoglu, E. M.; Miska, S. Z.; Takach, N.; Reed, T. (Informa UK Limited, 2009-01-01)
In this study, a layered cuttings transport model is developed for high-angle and horizontal wells, which can be used for incompressible non-Newtonian fluids as well as compressible non-Newtonian fluids (i.e., foams). The effects of major drilling parameters, such as flow rate, rate of penetration, fluid density, viscosity, gas ratio, cuttings size, cuttings density, wellbore inclination and eccentricity of the drillsting on cuttings transport efficiency are analyzed. The major findings from this study are,...
Modeling of underground gas storage in a depleted gas field
Gumrah, F; Izgec, O; Gokcesu, U; Bağcı, Ali Suat (Informa UK Limited, 2005-07-15)
It is possible to predict the behavior of fluids in permeable and porous medium under different operating conditions by using reservoir models. Since geological data and reservoir properties can be defined most accurately by reservoir models, it has been accepted as a reliable prediction tool among reservoir engineers. In this study, a gas reservoir has been modeled with IMEX Module of CMG Reservoir Simulator. Rock properties, gas composition and certain production data were entered to the model as input da...
Mathematical modeling of steam-assisted gravity drainage
Akın, Serhat (Society of Petroleum Engineers (SPE), 2005-01-01)
A mathematical model for gravity drainage in heavy-oil reservoirs and tar sands during steam injection in linear geometry is proposed. The mathematical model is based on the experimental observations that the steam-zone shape is an inverted triangle with the vertex fixed at the bottom production well. Both temperature and asphaltene content dependence on the viscosity of the drained heavy oil are considered. The developed model has been validated with experimental data presented in the literature. The heavy...
Analytical investigation of wet combustion process for heavy oil recovery
Bağcı, Ali Suat (Informa UK Limited, 2004-12-01)
Analysis of combustion tube data produced from experiments performed under realistic reservoir conditions is currently the most valid method of investigating in-situ combustion process. In this study, the optimization of water-air ratio for B. Kozluca heavy crude oil, and the comparison of the performance of dry and wet forward combustion processes were studied. An analytical model was used to extend the laboratory results so that the oil production and steam zone volume can be estimated under field conditi...
Citation Formats
M. E. Ozbayoglu and C. Omurlu, “Comparative study of yield-power law drilling fluids flowing through annulus,” PETROLEUM SCIENCE AND TECHNOLOGY, pp. 1041–1052, 2007, Accessed: 00, 2020. [Online]. Available: https://hdl.handle.net/11511/64781.