Elastic-plastic deformation of a heat generating tube with temperature-dependent yield stress

2000-01-01
Gulgec, M
Orcan, Y
The distribution of stress, plastic strain and displacement in an elastic-perfectly plastic tube with fixed ends in the presence of a uniform heat source is investigated analytically by taking into consideration the temperature dependence of the yield limit. The treatment is based on Tresca's yield condition and its associated flow rule. Depending on the radius ratio of the tube, in general, five different plastic regions, two of them corresponding to an edge regime of Tresca's prism, and an intermediate elastic region occur. Four different ranges of radius ratio of the tube can be distinguished which lead to different patterns of elastic-plastic deformation. In all cases the thermal load is increased up to the value for which the elastic region vanishes.
INTERNATIONAL JOURNAL OF ENGINEERING SCIENCE

Suggestions

Thermal stresses in elastic-plastic tubes with temperature-dependent mechanical and thermal properties
Orcan, Y; Eraslan, Ahmet Nedim (2001-11-01)
The thermoelastic-plastic deformations of internal heat-generating tubes are investigated by considering the temperature dependence of the thermal conductivity coefficient, Young's modulus, the coefficient of thermal expansion, and the yield limit of the material. A model describing the elastic-plastic behavior of the tube is developed. The model consists of a system of two second-order ordinary differential equations and a first-order ordinary differential equation involving nonlinear temperature-dependent...
Influence of the temperature dependence of the yield stress on the stress distribution in a heat-generating tube with free ends
Orcan, Y; Gulgec, M (2000-08-01)
Based on Tresca's yield condition and its associated flow rule, the elastic-plastic deformation of a heat-generating tube with free ends is investigated by taking into consideration the influence of the temperature dependence of the yield stress. It is found that the expansion of the inner plastic zones as well as the stress state are affected markedly owing to the reduction in the yield stress at elevated temperatures, The stress distribution and the expansion of different plastic regions are displayed gra...
Elastic-plastic deformation of a rotating solid disk of exponentially varying thickness
Eraslan, Ahmet Nedim (2002-07-01)
The elastic-plastic deformation of a rotating solid disk of variable thickness in exponential form is investigated using Tresca's yield criterion, its associated flow rule and linear strain hardening. An analytical solution is obtained and numerical results are presented for different values of the geometric parameters. In the limiting case of uniform thickness the solution reduces to Garner's solution.
Elastic-plastic stresses in linearly hardening rotating solid disks of variable thickness
Orcan, Y; Eraslan, Ahmet Nedim (2002-07-01)
The distribution of stress, displacement and plastic strain in a rotating elastic-plastic solid disk of variable thickness in a power function form is investigated. The analysis is based on Tresca's yield condition, its associated flow rule and linear strain hardening material behavior. An analytical solution is obtained and numerical results are presented for different values of the geometric parameters. The validity of the solution is demonstrated by comparing the results with those for a uniform thicknes...
Modulation of magnetism and study of impedance and alternating current conductivity of Zn0.4Ni0.6Fe2O4 spinel ferrite
Amor, S. B.; Benali, A.; Bejar, M.; Dhahri, E.; Khirouni, K.; Valente, M. A.; Graca, M. P. F.; Al-Turjman, F.; Rodriguez, J.; Radwan, A. (2019-05-15)
A spinel ferrite sample Zn0.4Ni0.6Fe2O4 was prepared by a conventional solid-state reaction method at high temperature. This compound was found to exhibit a single phase and crystallize in a cubic structure with Pm3 m Space group. The complex impedance was investigated in the temperature range 400-700 K and in the frequency range 100 Hz - 1 MHz. The Z-impedance analysis revealed that the relaxation phenomenon is strongly dependent on temperature and frequency. The impedance plane plot showed semi-circle arc...
Citation Formats
M. Gulgec and Y. Orcan, “Elastic-plastic deformation of a heat generating tube with temperature-dependent yield stress,” INTERNATIONAL JOURNAL OF ENGINEERING SCIENCE, pp. 89–106, 2000, Accessed: 00, 2020. [Online]. Available: https://hdl.handle.net/11511/66051.