Bond strength of a silicone soft lining material to poly(methyl methacrylate) resin treated with maleic anhydride and its terpolymers

2007-01-01
Turgut, Mehmet
Bolayir, Giray
Dogan, Orhan Murat
Keskin, Selda
Dogan, Arife
Boztug, Ali
Show full item record
Creative Commons License
This work is licensed under a Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.
207
views
0
downloads
This study investigated the effectiveness of surface treatment of Poly (methyl methacrylate) (PMMA) denture base resin on tensile bond strength between PMMA/silicone-based soft liner. A total of 25 specimens were fabricated and assigned into five groups (n = 5). The surfaces of PMMA were treated with maleic anhydride, maleic anhydride-styrene-vinyl-acetate, n-butylmaleate-styrene-vinyl-acetate, or n-pentamaleate-styrene-vinyl-acetate prior to Primo adhesive primer application and silicone liner placement. The Primo adhesive primer on applied group untreated dentuse base resin served as control. The tensile test was performed using a universal testing machine. Fractured surfaces were observed under Scanning Electron Microscopy (SEM) and spectroscopic interpretation of the interfaces was done by Fourier Transform Infrared (FTIR). Test results showed that surface treatment increased interfacial strength giving the highest value for n-butylmaleatestyrenevinyl acetate treated group. SEM micrographs revealed that the specimens with n-butylmaleate-styrene-vinyl-acetate and n-pentamaleate-styrene-vinylacetate terpolymers underwent cohesive failure. FTIR analysis indicated secondary interactions such as hydrogen bonding, possibly on acrylic resin surfaces, caused by the use of maleic anhydride and its terpolymers, and the adhesive.
Materials Chemistry, Mechanics of Materials, General Chemistry, Surfaces, Coatings and Films, Surfaces and Interfaces
https://hdl.handle.net/11511/68261
JOURNAL OF ADHESION
Department of Chemistry, Article

Suggestions

Microtensile Bond Strength of Self-Adhesive Resin-Based Dental Cement to Bleached Enamel
Tamam, Evsen; Keskin, Selda; Ucatasli, Mine Betuel (Informa UK Limited, 2010-01-01)
This study investigated the effectiveness of bleaching agents on the micro tensile bond strength (mu TBS) of self-adhesive luting cement and enamel. A total of 126 samples were prepared from the labial surfaces of permanent human maxillary central incisors and assigned into three groups with 42 samples each as: control, enamel bleached with 10% hydrogen peroxide (HP), and enamel bleached with 10% carbamide peroxide (CP). Rely X Unicem (R) (3 M, ESPE) was used as self-adhesive resin cement. The total testing...
Flexural and bonding properties of a denture base polymer treated with nitric acid or ultraviolet radiation before relining with Molloplast-b
Dogan, Orhan Murat; Keskin, Selda; Bolayir, Giray; Usanmaz, Ali; Bek, Buelent (Informa UK Limited, 2007-01-01)
This study investigated adhesive forces and flexural strength of acrylic resin denture base relined with Molloplast-B soft lining material. To increase bonding between the two materials, the surface of the resin was modified with ultraviolet (UV) irradiation or nitric acid treatment. The peel strength greatly increased with nitric acid treatment because of the high polarity on the poly (methyl methacrylate) (PMMA) surface and the increase in the surface roughness, whereas low peel strength was seen with the...
Tensile Bond Strength of a Highly Cross-Linked Denture Tooth to the Compression-Molded and Injection-Molded Denture Base Polymers
DOĞAN, ARİFE; Korkmaz, Turan; DOĞAN, ORHAN MURAT; Keskin, Selda; DEMİR, HAKAN (Informa UK Limited, 2009-01-01)
This study compared tensile bond strengths between conventional compression-molded heat (HC)-, auto (AP)-, and microwave-polymerized (MC) poly(methyl methacrylate)-based denture resins and a relatively new injection-molded, microwave-polymerized polyurethane based resin (MI) bonded to a highly cross-linked denture tooth. In the first part of the experiments, denture teeth were used as received. In the second part, they were treated with dichloromethane to see its effect on bonding of conventional denture ba...
Mechanical properties of soft liner-poly(methyl methacrylate)-based denture material
Usanmaz, Ali; Latifoglu, MA; Dogan, A; Akkas, N; Yetmez, M (Wiley, 2002-07-18)
In this study, the mechanical properties of two different permanent soft lining materials and their bonding to poly(methyl methacrylate) (PMMA) were compared. Both of the soft liners were heat-cured commercial materials. The polymerization was carried out by conventional methods suggested by manufacturer, and the curing was done at the temperature of boiling water for 5, 15, 25, and 35 min. The sample groups were tested in the computer-aided tensile-testing machine at a rate of 2 mm/min. The slow rate helps...
Curing characteristics of glycidyl azide polymer-based binders
Kasikci, H; Pekel, F; Özkar, Saim (Wiley, 2001-04-04)
The curing of a glycidyl azide polymer (GAP) with a triisocyanate, Desmodur N-100, was followed by measuring the hardness and viscosity. The thermal behavior of the cured samples were investigated by a differential scanning calorimeter (DSC) and thermal gravimetric analysis (TGA). Curing causes an increase in the glass transition temperature of GAP. The T-g of gumstocks also increases with an increasing NCO/OH ratio while the decomposition temperature remains practically unchanged. The ultimate hardness of ...
Citation Formats
M. Turgut, G. Bolayir, O. M. Dogan, S. Keskin, A. Dogan, and A. Boztug, “Bond strength of a silicone soft lining material to poly(methyl methacrylate) resin treated with maleic anhydride and its terpolymers,” JOURNAL OF ADHESION, pp. 927–938, 2007, Accessed: 00, 2020. [Online]. Available: https://hdl.handle.net/11511/68261.
METU IIS - Integrated Information Service open@metu.edu.tr