3 Boyutlu Yazım Tekniği ile Polikaprolakton Sinir Kılavuzu Üretimi

2018-12-14
Dursun Usal, Tuğba
Yücel, Deniz
Hasırcı, Vasıf Nejat
23. Biyomedikal Bilim ve Teknoloji Sempozyumu (BIOMED) ( 15 - 16 Aralık 2018)

Suggestions

3 Boyutlu yazıcı ile üretilen PLA bazlı yapıların mekanik özelliklerinin incelenmesi
Kaygusuz, Burçin; Özerinç, Sezer (Makina Tasarım ve İmalat Derneği , 2018-05-01)
3 boyutlu yazıcılar aracılığıyla üretilen bileşenler ve ürünler, otomotiv, biyomedikal, tekstil ve gıda sektörlerinde giderek artan oranda kullanılmaktadır. Bu yöntemle üretilen malzemelerin mekanik özelliklerinin anlaşılması, bu malzemelerin uygulamalarda verimli olarak kullanılması açısından önem taşımaktadır. Bu çalışmada en yaygın olarak kullanılan 3 boyutlu yazıcı malzemelerinden biri olan polilaktik asit ile üretilen yapılarda, nozul sıcaklığı ve dolgu yoğunluğu gibi parametrelerin mekanik özelliklere...
Aerodynamic design optimization using 3-dimensional euler equations and adjoint method
Yıldırım, Ali; Eyi, Sinan; Department of Aerospace Engineering (2017)
S-duct diffusers are often used for aircraft propulsion systems that convey the intake air to the engine compressor. In this thesis, flow structure at separated entrance conditions in an S-duct diffuser that designed for a micro turbojet engine powered aircraft is investigated using experimental and numerical methods. Flow characteristics such as flow separation, secondary flows, and swirl are investigated to find out the source of distortions and pressure loss at aerodynamics interface plane. Experiments a...
Fast feature extraction from 3D point cloud
Tarçın, Serkan; Özgen, Gökhan Osman; Department of Mechanical Engineering (2013)
To teleoperate an unmanned vehicle a rich set of information should be gathered from surroundings.These systems use sensors which sends high amounts of data and processing the data in CPUs can be time consuming. Similarly, the algorithms that use the data may work slow because of the amount of the data. The solution is, preprocessing the data taken from the sensors on the vehicle and transmitting only the necessary parts or the results of the preprocessing. In this thesis a 180 degree laser scanner at the f...
In-Service Mathematics Teachers’ Knowledge of Assessment Regarding the Volume of 3D Solids
Tekin Sitrava, Reyhan; Işıksal Bostan, Mine (2017-10-08)
The purpose of this study is to investigate in-service mathematics teachers’ knowledge of assessment related to students’ understanding of the volume of 3D solids. Throughout the study, knowledge of assessment refers to one of the dimensions of teachers’ PCK which comprises teachers' knowledge of what to assess and how to assess students’learning. The study is a qualitative case study. The data were collected from four in-service mathematics teachers via document analysis, inte...
Mechanical strength of 3D printed objects: experimental and numerical investigation
Başara, Gözde; Tarı, İlker; Department of Mechanical Engineering (2017)
The number of people and the industries that are using 3 Dimensional (3D) printing increases everyday; however, the home-use of 3D printing remains below expectations partially due to limitation in the printer size. Many different technolo-gies can be used in 3D printing. In this study Fused Deposition Modelling (FDM) is used. This method is commonly used for home-use 3D printing. In FDM, there is a wide range of materials that can be used and for this study the material is chosen as Poly Lactic Acid (PLA) ...
Citation Formats
T. Dursun Usal, D. Yücel, and V. N. Hasırcı, “3 Boyutlu Yazım Tekniği ile Polikaprolakton Sinir Kılavuzu Üretimi,” İstanbul, Türkiye, 2018, p. 115, Accessed: 00, 2021. [Online]. Available: https://docs.wixstatic.com/ugd/b78be8_655a9a1d523f4c72b60a6197c191acc3.pdf.