Characterization of Moganite Obtained From Natural Zeolite By Ball Milling

Sezer, Selda
The aim of this study is to investigate the effect of mechanical activation on the phase change of the zeolite composition of the Hekimhan region which is located in the northern of the Malatya Basin in Eastern Anatolia.Planetary mill was used for this study at different speeds and times. The laboratory experiments had shown that the microcrystalline moganite was formed at 450 rpm and 180 min and 540 rpm and 120 min, depending on the time and milling speed. Characterization studies of the zeolite and moganite (450 rpm/180min and as well 540 rpm/120 min) have done by XRD(X–Ray Diffraction), SEM (Scanning Electron Microscopy) images and FT–IR (Fourier–Transforms Infrared Spectroscopy).
American Journal of Engineering Research (AJER)


Characterization and Kinetics of Siberian and Tatarstan Regions Crude Oils Using Differential Scanning Calorimetry
Varfolomeev, M. A.; Rakipov, I. T.; Isakov, D. R.; Nurgaliev, D. K.; Kök, Mustafa Verşan (2015-01-01)
In this study, nonisothermal kinetics and thermal analysis of Siberian and Tatarstan regions crude oils is studied by differential scanning calorimetry (DSC) at different heating rates. DSC curves revealed two reaction regions in the temperature range of 20-600 degrees C, known as low and high temperature oxidation, respectively. Three different kinetic methods (ASTM, Borchardt and Daniels, and Roger and Morris) were used to determine the kinetic parameters of the samples and it was observed that the activa...
Characterization of lignocellulose biomass and model compounds by thermogravimetry
Kök, Mustafa Verşan (Informa UK Limited, 2017-01-01)
In this research, combustion characteristics of lignocellulose biomass (hazelnut shell) and three main components (cellulose, hemicellulose, and lignin) were investigated using thermogravimetry (TGA-DTG) technique at different heating rates. The ignition, peak, burn-out temperatures, and the heat liberation of lignocellulose biomass and three main components were also measured. Two different model-free kinetic methods, known as Ozawa-Flynn-Wall (OFW) and Kissinger-Akahira-Sunose (KAS), were used in order to...
Characterization of c-axis oriented Y-Ba-Cu-O thin films prepared by PVD on LaAlO3 (100) and SrTiO3 (100) substrates
Ozenbas, MA; Gungoren, T (Elsevier BV, 2000-11-01)
In this study, high T-c superconducting thin films of Y-Ba-Cu-O system have been prepared onto single crystals of LaAlO3 (100) and SrTiO3 (100) by resistive evaporation of YF3, BaF2 and Cu powders and a subsequent multi-stage annealing. In the deposition process, two different methods were used: mixed-powder method and sequential-deposition method. The best quality films were achieved on LaAlO3 substrates by using sequential-deposition technique with offset critical transition temperature of 88.1 K. Charact...
Analysis of the Raman intensities near the phase transitions in ammonium halides
Yurtseven, Hasan Hamit (Elsevier BV, 2008-12-01)
This study concentrates on the temperature dependence of the Raman intensities for the lattice modes in ammonium halides (NH4Cl and NH4Br) close to phase transitions, We predict their intensities using the results of a shell model for the Raman polarizability within the framework of an Ising pseudospin-phonon coupled model.
Synthesis and characterization of poly(dihalophenylene oxide)s and its derivatives from diammine bis(trihalophenolato) Cu(II) complexes
Sonsuz, Muammer; Gökağaç Arslan, Gülsün; Department of Chemistry (2004)
In this study, synthesis and characterization of poly(dihalophenylene oxide)s were done by thermal decomposition of diamminebis(trichlorophenolato) copper(II) and diamminebis(tribromophenolato) Cu(II) complexes in solid state. 2,4,6-trichlorophenol (TCP), 2,4,6-tribromophenol (TBP) and ammonia were used as ligands in the complex syntheses. The complexes were characterized by means of X-ray diffraction, FTIR, DSC, mass spectroscopy, magnetic susceptibility and C, H, N elemental analyses. Synthesized complexe...
Citation Formats
S. Sezer, “Characterization of Moganite Obtained From Natural Zeolite By Ball Milling,” American Journal of Engineering Research (AJER), vol. 7, no. 1, pp. 230–234, 2018, Accessed: 00, 2022. [Online]. Available: