Effect of gap distance on the mechanical properties and cross-sectional characteristics of the MIG-MAG butt wells

Download
2003
Kaşıkçı, İlker
This study was undertaken with the objective of determining the effect of gap distance on the weld bead geometry and the mechanical properties of the weldments. Low-alloyed and low carbon steel plates were welded under different conditions where each weldment had different gap distance and weld bead grooves. The influences of welding parameters namely, welding speed, current and voltage on the weld bead were examined in terms of weld bead penetration and heat affected zone and weld metal zone hardness variations.

Suggestions

Effect of swaging on microstructure and tensile properties of W-Ni-Fe alloys
DURLU, NURİ; Caliskan, N. Kaan; Bor, Sakir (Elsevier BV, 2014-01-01)
The objective of this study was to investigate the effect of swaging on the microstructure and tensile properties of high density two phase alloys 90W-7Ni-3Fe and 93W-4.9Ni-2.1Fe. Samples were liquid phase sintered under hydrogen and argon at 1480 degrees C for 30 min and then 15% cold rotary swaged. Measurement of microstructural parameters in the sintered and swaged samples showed that swaging slightly increased tungsten grain size in the longitudinal direction and slightly decreased tungsten grain size i...
Effect of particle shape on fall velocity of angular particles
Göğüş, Mustafa; Kokpinar, MA (2001-10-01)
In this study, fall velocities of 174 regularly shaped angular particles-namely cylindrical, cubic, wedge-shaped prisms, and box-shaped prisms-made of five different materials were measured in calm water conditions in a cylindrical settling column. Reynolds numbers based on particle fall velocity and characteristic length were varied, in the range from 10(3) to 4.2 x 10(4). A new shape factor and characteristic length were defined from a transformed form of the original particle. Variation of experimentally...
Effect of PTFE nanoparticles in catalyst layer with high Pt loading on PEM fuel cell performance
Avcioglu, Gokce S.; FIÇICILAR, BERKER; Eroğlu, İnci (Elsevier BV, 2016-06-22)
In this study, Polytetrafluoroethylene (PTFE) was added to catalyst layer structure. This modification was aimed at facilitating excess water removal from the cathode catalyst layer with high Pt loading (1.2 mg/cm(2)). The weight percentage of PTFE in the catalyst inks varied from zero to 30. Membrane electrode assemblies were prepared with a commercial catalyst containing 70 wt % Pt on carbon, by ultrasonic spray coating technique. PEM fuel cell performance testing was carried out with two different membra...
S235 Çeliğinin MAG Köşe Kaynağında Farklı Sabitleme Noktalarına Bağlı Gelişen Çarpılma Eğilimlerinin Sonlu Elemanlar Yöntemi ile Tahmin Edilmesi
Bedir, Elif; Batıgün, Caner; Gür, Cemil Hakan (null; 2015-11-21)
Bu çalışmada, S235 yapı çeliği plakalarına uygulanan MAG köşe kaynağı işlemi esnasında kullanılan sabitleme sisteminin yapıda meydana gelen deformasyon eğilimi üzerindeki etkisi incelenmiş ve deformasyonun önceden tayin edilebilirliği tartışılmıştır. Uygulanan sabitleme düzeninin yapıda kapladığı hangi faktörlere bağlı olduğu anlaşılmaya çalışılmıştır. Farklı sabitleme sistemleri kullanılarak MAG kaynağına tabi tutulan S235 tipi çelik plakalarda meydana gelecek olan deformasyon, “Weld Planner” yazılımı kull...
Effect of Flare Geometry on the Flow Field of Radial-Radial Swirlers
Bay, Ayse; Kiyici, Firat; Perçin, Mustafa (2022-01-01)
In this study, an experimental investigation is conducted to assess the impact of the flare geometry on the mean flow field generated by radial-radial swirlers. Two-dimensional two component PIV measurements are performed on the mid-plane of a non-reacting planar combustor test section. Three dimensional numerical simulations are conducted for selected cases to support experimental observations. In a previous study conducted in the same setup, counter-rotating radial-radial swirlers without flare extension ...
Citation Formats
İ. Kaşıkçı, “Effect of gap distance on the mechanical properties and cross-sectional characteristics of the MIG-MAG butt wells,” M.S. - Master of Science, Middle East Technical University, 2003.