Implementation of sensorless vector control drive with current position estimation

Download
index.pdf
2016
Filci, Tayfun
Show full item record
222
views
154
downloads
In this thesis, an algorithm will be developed and implemented online for the estimation of rotor position from the rotor slot harmonics in stator currents. Experiments will be done on an inverter driven induction motor hardware, and the performance of the position detection algorithm will be evaluated in comparison with commercial encoder outputs.
Electric motors, Induction., Electric machinery, Electric machinery, Induction., Electric machinery
http://etd.lib.metu.edu.tr/upload/12619959/index.pdf
https://hdl.handle.net/11511/25626
Graduate School of Natural and Applied Sciences, Thesis

Suggestions

An FPA based BLDC motor control system
Uygur, Serdar; Güran, Hasan Cengiz; Department of Electrical and Electronics Engineering (2012)
In this thesis, position and current control systems for a brushless DC (Direct Current) motor are designed and integrated into one FPGA (Field Programmable Gate Array) chip. Experimental results are obtained by driving the brushless DC motors of Control Actuation System of a guided missile. Because of their high performance, brushless DC motors are widely used in Control Actuation Systems of guided missiles. In order to control the motor torque, current controller is designed and implemented in the FPGA. P...
Implementation of a vector controlled induction motor drive
Acar, Akın; Ertan, Hulusi Bülent; Department of Electrical and Electronics Engineering (2004)
High dynamic performance, which is obtained from dc motors, became achievable from induction motors with the recent advances in power semiconductors, digital signal processors and development in control techniques. By using field oriented control, torque and flux of the induction motors can be controlled independently as in dc motors. The control performance of field oriented induction motor drive greatly depends on the correct stator flux estimation. In this thesis voltage model is used for the flux estima...
Beforehand obtaining a safety operation condition by using daily load curves in transient stability and graphical software for transient stability applications
Öztop, Celal; Ertaş, Arif; Department of Electrical and Electronics Engineering (2005)
In this thesis, relationship between two most important transient stability indices, critical clearing time and generator rotor angle is examined for one machine-infinite bus system and then extended to the multimachine case and is observed to be linear. By using the linear relationship between critical clearing time and generator rotor angle and utilizing the daily load curve, a new preventive method is proposed. The aim of this method is to make all critical clearing times longer than the relay and circui...
Adaptive control of DC link current in current source converter based STATCOM for improving its power losses
Karaduman, Ferdi; Ermiş, Muammer; Bilgin, Hazım Faruk; Department of Electrical and Electronics Engineering (2012)
In conventional three-phase PWM (Pulse Width Modulation) current source converter based STATCOM (Static Synchronous Compensator) applications, DC link current is kept constant at a predefined value and the reactive power of STATCOM is controlled by varying modulation index. This control strategy causes unnecessary power losses especially when the reactive power of STATCOM is low. For this purpose, in order to reduce the active power drawn by STATCOM, the modulation index can be maximized by adjusting DC lin...
Modeling and design of iron-core shunt reactors with discretely distributed air-gaps
Dönük, Atilla; Ermiş, Muammer; Bilgin, Hazım Faruk; Department of Electrical and Electronics Engineering (2012)
In this research work detailed parallel and series equivalent circuits of a gapped iron-core shunt reactor with discretely distributed gaps are derived. The validity of the recommended equivalent circuits is verified by Finite Element Analysis and laboratory tests. Effects of fringing flux and discretely distributed gaps on inductance parameters and reactor losses are also investigated. Moving Strip Method for discretely distributed gapped shunt reactors is recommended. Two design procedures for shunt react...
Citation Formats
T. Filci, “Implementation of sensorless vector control drive with current position estimation,” M.S. - Master of Science, Middle East Technical University, 2016.
METU IIS - Integrated Information Service open@metu.edu.tr