Low-cost uncooled infrared detector arrays in standard CMOS

2003-04-25
Eminoglu, S
Tanrikulu, MY
Akın, Tayfun
This paper reports the development of a low-cost 128 x 128 uncooled infrared focal plane array (FPA) based on suspended and thermally isolated CMOS p(+)-active/n-well diodes. The FPA is fabricated using a standard 0.35 mum CMOS process followed by simple post-CMOS bulk micromachining that does not require any critical lithography or complicated deposition steps; and therefore, the cost of the uncooled FPA is almost equal to the cost of the CMOS chip. The post-CMOS fabrication steps include an RIE etching to reach the bulk silicon and an anisotropic silicon etching to obtain thermally isolated pixels. During the RIE etching, CMOS metal layers are used as masking layers, and therefore, narrow openings such as 2 gm can be defined between the support arms. This approach allows achieving small pixel size of 40 mum x 40 mum with a fill factor of 44 %. The FPA is scanned at 30 fps by monolithically integrated multi-channel parallel readout circuitry which is composed of low-noise differential transconductance amplifiers, switched capacitor (SC) integrators, sample-and-hold circuits, and various other circuit blocks for reducing the effects of variations in detector voltage and operating temperature. The fabricated detector has a temperature coefficient of -2 mV/K, a thermal conductance value of 1.8 x 10(-7) W/K, and a thermal time constant value of 36 msec, providing a measured DC responsivity (R) of 4970 V/W under continuous bias. Measured detector noise is 0.69 muV in 8 kHz bandwidth at 30 fps scanning rate, resulting a measured detectivity (D*) of 9.7 x 10(8) cmrootHz/W. Contribution of the 1/f noise component is found to be negligible due to the single crystal nature of the silicon n-well and its low value at low bias levels. The noise of the readout circuit is measured as 0.76 muV, resulting in an expected NETD value of 1 K when scanned at 30 fps using f=1 optics. This NETD value can be decreased below 350 mK by decreasing the electrical bandwidth with the help of increased number of parallel readout channels and by optimizing the post-CMOS etching steps. The uniformity of the array is very good due to the mature CMOS fabrication technology. The measured uncorrected differential voltage non-uniformity for the 128 x 128 array pixels after the CMOS fabrication is 0.2 % with a standard deviation of only 1.5 mV, which is low due to the improved array structure that can compensate for the voltage drops along the routing resistances in the array. Non-uniformity of temperature sensitivity of the array pixels is measured to be less than 3 % with a mean and standard deviation of -2.05 mV/K and 61 muV/K, respectively. The temperature sensitivity of the differential pixel voltages has a measured mean value of 2.3 muV/K, relaxing the requirements on the temperature stabilization. Considering its performance and its simple fabrication steps, the proposed method is very cost-effective to fabricate large format focal plane arrays for low-cost infrared imaging applications.
Infrared Technology and Applications XXIX Conference

Suggestions

High performance HgCdTe photodetector desings via dark current suppression
Özer, Yiğit; Kocaman, Serdar; Department of Electrical and Electronics Engineering (2018)
This thesis work covers the numerical analysis and design of infrared photon detectors with a focus of HgCdTe based devices. An in-house numerical tool is utilized for the design and characterization process, where the Poisson, current and continuity equations are solved numerically with the high precision in electrical and optical properties. A high operating temperature alternative substrate mid-wave HgCdTe detector is designed benefiting from the generation-recombination dark current suppression. The adv...
A low-cost 128x128 uncooled infrared detector array in CMOS process
Eminoglu, Selim; Tanrikulu, Mahmud Yusuf; Akın, Tayfun (2008-02-01)
This paper discusses the implementation of a low-cost 128 x 128 uncooled infrared microbolometer detector array together with its integrated readout circuit (ROC) using a standard 0.35 mu m n-well CMOS and post-CMOS MEMS processes. The detector array can be created with simple bulk-micromachining processes after the CMOS fabrication, without the need for any complicated lithography or deposition steps. The array detectors are based on suspended p(+)-active/n-well diode microbolometers with a pixel size of 4...
A low-cost small pixel uncooled infrared detector for large focal plane arrays using a standard CMOS process
Eminoglu, S; Tanrikulu, MY; Tezcan, DS; Akın, Tayfun (2002-04-03)
This paper reports the development of a low-cost, small pixel uncooled infrared detector using a standard CMOS process. The detector is based on a suspended and thermally isolated p(+)-active/n-well diode whose forward voltage changes due to an increase in the pixel temperature with absorbed infrared radiation. The detector is obtained with simple post-CMOS etching steps on dies fabricated using a standard n-well CMOS process. The post-CMOS process steps are achieved without needing any deposition or lithog...
High performance focal plane array technologies from short to long wavelength infrared bands
Arslan, Yetkin; Beşikci, Cengiz; Department of Electrical and Electronics Engineering (2014)
This thesis work covers the development of three different state of the art infrared sensor technologies: quantum well infrared photodetectors (QWIPs), HgCdTe sensors and extended InGaAs photodetectors. QWIP is the leading member of the quantum structure infrared photodetector family providing excellent uniformity and stability with field proven performance. The utilization of the InP/In0.48Ga0.52As multi-quantum well structure (instead of the standard AlGaAs/GaAs material system) for the implementation of ...
An uncooled microbolometer infrared focal plane array in standard CMOS
Tezcan, Ds; Eminoglu, S; Akar, Os; Akın, Tayfun (2001-01-24)
This paper reports implementation of a low-cost microbolometer focal plane array using n-well layer in a CMOS process as the microbolometer material. N-well microbolometer structures are suspended for thermal isolation by postetching of fabricated CMOS dies using silicon bulk-micromachining techniques. Although n-well has a moderate TCR of 0.5-0.65 %/K at 300 K, it still provides a reasonable performance due to its single crystal structure which contributes low 1/f noise. Detailed thermal simulations in ANS...
Citation Formats
S. Eminoglu, M. Tanrikulu, and T. Akın, “Low-cost uncooled infrared detector arrays in standard CMOS,” Orlando, FL, 2003, vol. 5074, Accessed: 00, 2020. [Online]. Available: https://hdl.handle.net/11511/38460.