A STEREO LINE MATCHING TECHNIQUE FOR AERIAL IMAGES BASED ON A PAIR-WISE RELATION APPROACH

2010-10-13
Ok, Ahmet
Heipke, C.
Rottensteiner, F.
Soergel, U.
Toprak, V.
In this study, we developed a new pair-wise relation based approach for the matching of line features from stereo aerial images. To solve the final matching inconsistencies, we propose an iterative pair based post-processing algorithm in which the matching inconsistencies are eliminated using three novel measures and a final similarity voting scheme. The approach is tested over four urban test sites with various built-up characteristics, and for all test sites, we achieved a stereo line matching performance of 98%. The overall results indicate that the proposed approach is highly robust for the line features extracted in (very) dense urban areas.
ISPRS Istanbul Workshop on Modeling of Optical Airborne and Spaceborne Sensors

Suggestions

A NEW STRAIGHT LINE RECONSTRUCTION METHODOLOGY FROM MULTI-SPECTRAL STEREO AERIAL IMAGE
Ok, Ahmet; Heipke, C.; Rottensteiner, F.; Soergel, U.; Toprak, V. (2010-09-03)
In this study, a new methodology for the reconstruction of line features from multispectral stereo aerial images is presented. We take full advantage of the existing multispectral information in aerial images all over the steps of pre-processing and edge detection. To accurately describe the straight line segments, a principal component analysis technique is adapted. The line to line correspondences between the stereo images are established using a new pair-wise stereo matching approach. The approach involv...
AN AUTOMATIC MODE MATCHING SYSTEM FOR A HIGH Q-FACTOR MEMS GYROSCOPE USING A DECOUPLED PERTURBATION SIGNAL
Yesil, F.; Alper, S. E.; Akın, Tayfun (2015-06-25)
This paper reports a closed-loop controller system developed for in-run automatic matching of the drive and sense mode resonance frequencies of a MEMS gyroscope with a high quality factor (Q). This is achieved by injecting a perturbation signal to the quadrature cancellation loop, while keeping it decoupled from the angular rate control loop. The new controller is implemented in a CMOS ASIC together with the other sensor control loops, and it is verified to maintain matched-mode state under changing environ...
Design and fabrication of a detector logarithmic video amplifier
Dinç, Mustafa Barış; Yıldırım, Nevzat; Department of Electrical and Electronics Engineering (2011)
In this thesis a single stage detector logarithmic video amplifier is designed with a dynamic range of 40dB in 2-6GHz frequency band. Since the detector logarithmic video amplifier (DLVA) is used to convert the power of the RF signals to video voltages in logarithmic scale, it can be regarded as a logarithmic converter instead of logarithmic amplifier. The design is composed of two main parts: The Schottky diode detector rectifies the incoming RF signal and produces a video voltage and the logarithmic ampli...
Accurate Reconstruction of Near-Epipolar Line Segments from Stereo Aerial Images
Ok, Ali Ozgun; Wegner, Jan Dirk; Heipke, Christian; Rottensteiner, Franz; Soergel, Uwe; Toprak, Vedat (2012-01-01)
In this study, a new 3D reconstruction approach for line segments from stereo images is proposed which covers the case that the image lines are nearly-aligned (<= 10 degrees) with the epipolar line. The method manipulates the redundancy inherent in line pair-relations to generate artificial 3D points and utilizes those entities during the estimation process to improve the reconstruction of the line segments. The best points for the reconstruction are selected based on a newly proposed weight function. To te...
A reconfigurable RF MEMS triple stub impedance matching network
Unlu, M.; Topalli, K.; Atasoy, H.I.; Temocin, E.U.; Istanbulluoglu, I.; Bayraktar, O.; Demir, Şimşek; Civi, O.A.; Koç, Seyit Sencer; Akın, Tayfun (2006-09-12)
This paper presents a reconligurable triple stub impedance matching network using RF MEMS technology centered at 10GHz. The device is capable of covering impedances on the whole Smith Chart. The device structure consists of three variable length stubs which are designed as distributed MEMS transmission lines and two lambda(g)/8 length CPW transmission fines connecting the stubs. The variable length stubs are implemented with 12 MEMS switches over CPW lines and CPW lines connecting the switches. lambda(g)/8 ...
Citation Formats
A. Ok, C. Heipke, F. Rottensteiner, U. Soergel, and V. Toprak, “A STEREO LINE MATCHING TECHNIQUE FOR AERIAL IMAGES BASED ON A PAIR-WISE RELATION APPROACH,” presented at the ISPRS Istanbul Workshop on Modeling of Optical Airborne and Spaceborne Sensors, Istanbul, TURKEY, 2010, Accessed: 00, 2020. [Online]. Available: https://hdl.handle.net/11511/54478.