Pressure Dependence of Molar Volume near the Melting Point in Benzene

Date

2007-10-01

Author

Yurtseven, Hasan Hamit

Metadata

Show full item record

This work is licensed under a Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.

Item Usage Stats

236
views

0
downloads

The pressure dependence of the molar volume was at constant temperatures close to the melting point in benzene. The molar volume of benzene was calculated using experimental data for the thermal expansivity for constant temperatures of 25°C, 28.5°C, 40°C, and 51°C at various pressures for both the solid and liquid phases. The predictions are in good agreement with the observed volumes in both the solid and liquid phases of benzene. The predicted values of the molar volume for a constant temperature of 28.5°C in the liquid phase of benzene agree well with experimental data in the literature.

Subject Keywords

Multidisciplinary

URI

https://hdl.handle.net/11511/57505

Journal

Tsinghua Science and Technology

DOI

https://doi.org/10.1016/s1007-0214(07)70143-8

Collections

Department of Physics, Article

Suggestions

OpenMETU
Core

Afterglow, TL and OSL properties of Mn2+-doped ZnGa2O4 phosphor Luchechko, Andriy; Zhydachevskyy, Yaroslav; Ubizskii, Sergii; Kravets, Oleh; Popov, Anatoli I.; Rogulis, Uldis; Elsts, Edgars; Bulur, Enver; Suchocki, Andrzej (Springer Science and Business Media LLC, 2019-07-02) Zinc gallate (ZnGa2O4) spinel ceramics doped with Mn2+ ions was prepared by a solid-state reaction at 1200 degrees C in air. Manganese concentration was equal to 0.05 mol.% of MnO with respect to ZnO. Ceramics produced in this way show an efficient green emission at about 505 nm under UV or X-ray excitations, which is caused by Mn2+ ions. This green emission is observed also as a relatively long afterglow (visible to the naked eye in the dark for about one hour) after switching-off the X-ray excitation. Tim...
Pressure dependence of the heat capacity near the melting point in benzene Yurtseven, Hasan Hamit (2017-09-01) The heat capacity C-p is calculated as a function of pressure at constant temperatures of 25, 40 and 51 degrees C for the solid and liquid phases of benzene near the melting point. For this calculation, the observed molar volume from the literature are used at various pressures for constant temperatures indicated through the thermodynamic relations in the solid and liquid phases of benzene near the melting point.
High strength metallic wood from nanostructured nickel inverse opal materials Pikul, James H.; Özerinç, Sezer; Liu, Burigede; ZHANG, Runyu; BRAUN, Paul V.; Deshpande, Vikram S.; KING, William P. (Springer Science and Business Media LLC, 2019-01-24) This paper describes a nickel-based cellular material, which has the strength of titanium and the density of water. The material's strength arises from size-dependent strengthening of load-bearing nickel struts whose diameter is as small as 17 nm and whose 8 GPa yield strength exceeds that of bulk nickel by up to 4X. The mechanical properties of this material can be controlled by varying the nanometer-scale geometry, with strength varying over the range 90-880 MPa, modulus varying over the range 14-116 GPa,...
Application of Electric Resistance Heating Method on Titanium Hot Forming at Industrial Scale Ozturk, Fahrettin; Ece, Remzi Ecmel; Polat, Naki; Koksal, Arif; Evis, Zafer; Sheikh-Ahmad, Jamal Y. (Springer Science and Business Media LLC, 2016-11-01) In this study, hot forming of DIN WL 3.7024 commercially pure titanium with a sheet thickness of 0.6 mm was performed by electric resistance heating. The sheet materials were heated at 600, 650, and 680 A degrees C and then hot formed with an industrial press. Grain size measurement and XRD analysis were performed for each forming temperature in order to investigate microstructure and phase changes. Results indicate that no microstructural changes have occurred at the mentioned temperature range. It was con...
Temperature and pressure dependence of molar volume in solid phases of ammonia near the melting point Yurtseven, Hasan Hamit (Elsevier BV, 2008-08-20) Temperature and pressure dependencies of the molar volume are studied here along the transition curve between solid I and solid II phases near the melting point in ammonia. The molar volumes are calculated in the temperature range of 217 to 224 K and in the pressure range of 3 to 8 kbar with respect to the triple point (T-t=217.34 K. P-t=3.070 kbar) where the melting curves of solid I and solid II coincide with the transition curve in ammonia.

Citation Formats

H. H. Yurtseven, “Pressure Dependence of Molar Volume near the Melting Point in Benzene,” Tsinghua Science and Technology, pp. 624–628, 2007, Accessed: 00, 2020. [Online]. Available: https://hdl.handle.net/11511/57505.