Development of a 3 axes PC numerical control system for industrial applications

Download
2003
Başar, Feza
In this study, a three-axes PC numerical control system for industrial applications has been developed. With this system, fast and cheap prototyping of designed objects can be realized. The system consists of software and a hardware which includes an XYZ positioning table and three step motors controlling this table. A proper drive circuit for the stepper motors is utilized. The software digitizes two dimensional drawings of three dimensional objects and generates the control signals for the XYZ positioning table. The software is developed under Microsoft Studio Visual Basic 6.0 environment regardless of the OS of the PC. The parallel port of the PC has been utilized for generating the necessary control signals for the stepper motors.

Suggestions

Design of a GaN Based Integrated Modular Motor Drive
Uğur, Mesut; Keysan, Ozan (2018-10-25)
In this study, design procedure of an Integrated Modular Motor Drive (IMMD) is presented focusing on high power density. The design is based on a permanent magnet synchronous motor (PMSM) and GaN FETs. Fractional slot concentrated windings are used on the stator. Slot/pole combination and winding configuration is selected based on having low cogging torque and high winding factor. An extended motor drive inverter topology is proposed where 2-level voltage source inverters are connected both in series and pa...
Comparison of Inverter Topologies Suited for Integrated Modular Motor Drive Applications
Ugur, Mesut; Sarac, Hakan; Keysan, Ozan (2018-08-30)
In this paper, various inverter topologies are compared for integrated modular motor drive (IMMD) applications. Two-level voltage source inverter (2L-VSI), three level voltage source inverter (3L-VSI) and series/parallel combinations of these topologies with system level modularity are compared in terms of voltage and current harmonic spectrum, passive component sizes and motor drive efficiency. New generation wide band-gap GaN power semiconductor devices are utilized in modular topologies and they are comp...
Tümleşik Modüler Motor Sürücü Sistemi Tasarımı
Uğur, Mesut; Keysan, Ozan (null; 2017-10-25)
Bu çalışmada, bir Tümleşik Modüler Motor Sürücü (TMMS) sistemi tasarımı gerçekleştirilmiştir. TMMS sistemi için modüler bir kesirli oluklu, konsantre sargılı (FSCW), sabit mıknatıslı senkron motor (PMSM) ile birlikte Galyum Nitrat (GaN) teknolojisine dayalı modüler motor sürücü güç katı tasarımı yapılmıştır. Konvansiyonel sistemlere göre %2’lik verim artışı sağlanmıştır. Tümleşik motor sürücü sistemine uygun DA bara kondansatör seçimi gerçekleştirilmiştir. Interleaving tekniği kullanılarak kondansatör boyut...
INVESTIGATION AND OPTIMIZATION OF WINGLETS FOR HAWT ROTOR BLADES
Elfarra, Monier A.; Akmandor, I. Sinan; Sezer Uzol, Nilay (2011-03-25)
The main purpose of this paper is to optimize winglet geometry by using CFD with Genetic Algorithm and study its effects on power production. For validation and as a baseline rotor, the NREL Phase VI wind turbine rotor blade is used. The Reynolds-Averaged Navier-Stokes equations are solved and different turbulence models including the Spalart-Allmaras, k-epsilon Launder-Sharma, k-epsilon Yang-Shih and SST k-omega models are used and tested. The results of the power curve and the pressure distribution at dif...
Application of genetic algorithms to calibration and verification of QUAL2E
Göktaş, Recep Kaya; Aksoy, Ayşegül; Department of Environmental Engineering (2004)
The objective of this study is to develop a calibration and verification tool for the QUAL2E Model by using Genetic Algorithms. In the developed optimization model, an objective function that is formulated on the basis of the sum-of-least squares approach aiming at minimizing the difference between the observed and simulated quantities was used. In order to perform simultaneous calibration and verification, verification of the calibrated results was treated as a constraint and inserted into the objective fu...
Citation Formats
F. Başar, “Development of a 3 axes PC numerical control system for industrial applications,” M.S. - Master of Science, Middle East Technical University, 2003.