Calculation of parameters of single-phase PM motor for design optimization

2005-09-01
Ertan, Hulusi Bülent
Capolino, GA
This paper presents methods of calculation of parameters of single-phase permanent-magnet (SPPM) motor, in terms of motor dimensions and material properties, which are utilized in the dynamic model of the motor. The intention of the study is to develop means of SPPM performance calculations, which lend themselves to be employed within a mathematical design optimization approach. The calculated parameters are compared with measured values and are shown to be accurate for the purpose of the study.
IEEE TRANSACTIONS ON ENERGY CONVERSION

Suggestions

Determination of rotor slot number of an induction motor using an external search coil
Keysan, Ozan; Ertan, Hulusi Bülent (null; 2009-12-01)
This paper describes determination of the number rotor slots of an induction motor from the induced emf in an external search coil. This information is needed in prediction of motor speed from the external search coil induced voltage. The approach is based on identifying saliency harmonics and rotor slot harmonics, via FFT analysis of the external search coil emf. The proposed approach is tested on an induction motor driven by the mains supply. The experiments are repeated with a PWM supply. It is shown tha...
Prediction of motor speed for low cost induction motor drives
Özlü Ertan, Hatice Gülçin (2006-05-19)
In this paper speed estimation methods for low cost, variable frequency induction motor drives are investigated. Such methods are required to minimize the computational effort and show little parameter dependence. Existing methods have limitations regarding the speed range or are applicable only if the motor size is such that certain requirements are met. Two methods described in the literature are considered. Three new methods of speed estimation are developed to improve their performance. The model used f...
Design of a GaN Based Integrated Modular Motor Drive
Uğur, Mesut; Keysan, Ozan (2018-10-25)
In this study, design procedure of an Integrated Modular Motor Drive (IMMD) is presented focusing on high power density. The design is based on a permanent magnet synchronous motor (PMSM) and GaN FETs. Fractional slot concentrated windings are used on the stator. Slot/pole combination and winding configuration is selected based on having low cogging torque and high winding factor. An extended motor drive inverter topology is proposed where 2-level voltage source inverters are connected both in series and pa...
Tümleşik Modüler Motor Sürücü Sistemi Tasarımı
Uğur, Mesut; Keysan, Ozan (null; 2017-10-25)
Bu çalışmada, bir Tümleşik Modüler Motor Sürücü (TMMS) sistemi tasarımı gerçekleştirilmiştir. TMMS sistemi için modüler bir kesirli oluklu, konsantre sargılı (FSCW), sabit mıknatıslı senkron motor (PMSM) ile birlikte Galyum Nitrat (GaN) teknolojisine dayalı modüler motor sürücü güç katı tasarımı yapılmıştır. Konvansiyonel sistemlere göre %2’lik verim artışı sağlanmıştır. Tümleşik motor sürücü sistemine uygun DA bara kondansatör seçimi gerçekleştirilmiştir. Interleaving tekniği kullanılarak kondansatör boyut...
Comparison of Inverter Topologies Suited for Integrated Modular Motor Drive Applications
Ugur, Mesut; Sarac, Hakan; Keysan, Ozan (2018-08-30)
In this paper, various inverter topologies are compared for integrated modular motor drive (IMMD) applications. Two-level voltage source inverter (2L-VSI), three level voltage source inverter (3L-VSI) and series/parallel combinations of these topologies with system level modularity are compared in terms of voltage and current harmonic spectrum, passive component sizes and motor drive efficiency. New generation wide band-gap GaN power semiconductor devices are utilized in modular topologies and they are comp...
Citation Formats
H. B. Ertan and G. Capolino, “Calculation of parameters of single-phase PM motor for design optimization,” IEEE TRANSACTIONS ON ENERGY CONVERSION, pp. 538–548, 2005, Accessed: 00, 2020. [Online]. Available: https://hdl.handle.net/11511/31812.