Determination of Internal Stress of Ni Electroplated Samples in Sulphamate Solutions

2017-06-01
Aykac, B.
Erdogan, M.
Karakaya, İshak
Internal stress is a common problem affecting the functionality of the electroplated materials. The parameters of electrodeposition and additive materials that are soluble in the bath change the characteristics of the plating and affect the internal stress of the coatings. The influence of the electrodeposition parameters on the internal stress of Ni deposits from the nickel sulphamate baths were studied by the help of fractional factorial design. The parameters included temperature, pH, current density and bath composition. Increasing temperature and deposit thickness, and decreasing boric acid and chloride ions resulted in decreasing the internal stress within the parameter ranges covered in this study.

Suggestions

On annular disks of variable thickness subjected to external pressure
Eraslan, Ahmet Nedim (Springer Science and Business Media LLC, 2004-02-01)
Exact solutions are obtained for the elastic stress distribution in variable thickness annular disks under external pressure. Two different thickness functions both in parabolic form are considered. It is shown that, depending on the geometric parameters describing the shape of the disk profile, the plastic deformation in the variable thickness annular disk commences at the inner or at the outer or simultaneously at both surfaces. The critical values of the geometric parameters which cause the plastic defor...
Yielding of two-layer shrink-fitted composite tubes subject to radial pressure
Eraslan, Ahmet Nedim (Springer Science and Business Media LLC, 2005-12-01)
Yielding of two-layer shrink-fitted composite tubes with axially constrained ends subject to either internal or external pressure is investigated in detail. In the framework of small deformations, a state of plane strain and von Mises yield criterion, analytical expressions are obtained for critical values of the pressure leading to plastic flow. It is shown that, depending on material properties and tube dimensions, different modes of plastic deformation may occur. Yielding may commence at the inner tube o...
Investigating Dynamics of Machine Tool Spindles under Operational Conditions
Özşahin, Orkun; Özgüven, Hasan Nevzat (2011-05-13)
Chatter is one of the major problems in machining and can be avoided by stability diagrams which are generated using frequency response functions (FRF) at the tool tip. During cutting operations, discrepancies between the stability diagrams obtained by using FRFs measured at the idle state and the actual stability of the process are frequently observed. These deviations can be attributed to the changes of machine dynamics under cutting conditions. In this paper, the effects of the cutting process on the spi...
Investigation of Au-Ag-Cu Alloy Electrodeposition to Electromechanical Systems
Cagan, Berkay; ERDOĞAN, METEHAN; Karakaya, İshak; Yilmaz, Cemil; Yurdakul, Burak (2020-04-01)
© 2020 ECS - The Electrochemical Society.Electromechanical systems, which provide electrical power and data connection between moving terminals require high conduction and erosion resistant surfaces. Transfers of electrical power and data are accomplished by the contact of drum and brush wires. The simultaneous electrochemical deposition of desired Au-Ag-Cu alloy compositions, which can be used to coat the brush wires, was investigated in this study. In the scope of the study, the static potential and cycli...
A computational procedure for estimating residual stresses and secondary plastic flow limits in nonlinearly strain hardening rotating shafts
Eraslan, Ahmet Nedim (Springer Science and Business Media LLC, 2005-03-01)
A computational procedure to estimate the residual stress distributions and the limit angular speeds for avoiding secondary plastic deformation in nonlinearly strain hardening rotating elastic-plastic shafts is given. The model is based on von Mises yield condition, J(2) deformation theory and a Swift-type hardening law. The boundary value problem for the governing nonlinear differential equation is solved by a shooting method using Newton iterations with numerically approximated tangent. Solid as well as h...
Citation Formats
B. Aykac, M. Erdogan, and İ. Karakaya, “Determination of Internal Stress of Ni Electroplated Samples in Sulphamate Solutions,” 2017, vol. 77, Accessed: 00, 2020. [Online]. Available: https://hdl.handle.net/11511/38544.