Effects of engine operating conditions on morphology, microstructure, and fractal geometry of light-duty diesel engine particulates

Date

2005-01-01

Author

ZHU, JİNYU
LEE, KYEONG OOK
Yozgatlıgil, Ahmet
CHOI, MUN YOUNG

Metadata

Show full item record

This work is licensed under a Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.

Item Usage Stats

115
views

0
downloads

An investigation on the morphology, internal microstructure, and fractal geometry of particulate matter (PM) was conducted for a 1.7-L light-duty diesel engine. The experimental and analytical instruments used in this study include a unique thermophoretic sampling system, a high-resolution transmission electron microscope (TEM), customized digital image processing/data acquisition system, and a Raman scattering spectrometer that have been extensively used at Argonne National Laboratory. During experiments, diesel particulates were directly collected from the exhaust stream. In the morphological observations using TEM, graphitic crystallite structures were found from these light-duty diesel particulates, particularly at high engine loads. In subsequent analysis, Raman spectra revealed details of these graphitic structures quantitatively: the collected diesel PM was quite similar in atomic structures to typical graphite, and the degree of its crystalline structures increased as the engine load increased. in PM size measurements, mean primary particle diameters (d(p)) are in a range of 19.4-32.5 nm and radii of gyration (R,) in a range of 77.4-134.1 urn, respectively, across the engine operating conditions of 780-4000 rpm and 0-100%, loads. From the fractal analysis, smaller fractal dimensions (D-f) (1.46-1.70) were measured for the light-duty diesel engine used in this study, compared to those of heavy-duty diesel particulates that ranged in 1.80-1.88. This result implies that more stretched chain-like particles were produced from the light-duty engine under the diffusion-limit formation mechanism. The database on the physical dimension and fractal geometry of light-duty diesel PM obtained from this study offers data for the future standards of diesel PM sizes and development of advanced diesel PM emission control technologies. (c) 2004 The Combustion Institute. Published by Elsevier Inc. All rights reserved.

Subject Keywords

Physical and Theoretical Chemistry, Mechanical Engineering, General Chemical Engineering

URI

https://hdl.handle.net/11511/41427

Journal

PROCEEDINGS OF THE COMBUSTION INSTITUTE

DOI

https://doi.org/10.1016/j.proci.2004.08.232

Collections

Department of Mechanical Engineering, Article

Suggestions

OpenMETU
Core

CO2 addition and pressure effects on laminar and turbulent lean premixed CH4 air flames Cohé, Cecile; Chauveau, Christian; Goekalp, Iskender; Kurtuluş, Dilek Funda (Elsevier BV, 2009-01-01) An experimental study on CH4-CO2-air flames at various pressures is conducted by using both laminar and turbulent Bunsen flame configurations. The aim of this research is to contribute to the characterization of fuel lean methane/carbon dioxide/air premixed laminar and turbulent flames at different pressures, by studying laminar and turbulent flame propagation velocities, the flame surface density and the instantaneous flame front wrinkling parameters. PREMIX computations and experimental results indicate a...
DETERMINATION OF MOISTURE DIFFUSIVITY AND BEHAVIOR OF TOMATO CONCENTRATE DROPLETS DURING DRYING IN AIR KARATAS, S; ESIN, A (Informa UK Limited, 1994-01-01) The drying mechanism and diffusion coefficient of water in spherical droplets (1.73 - 2.08 mm diameter) of tomato concentrates were successfully interpreted and modelled by using Fick's law. Solids content of the initial concentrate (5-15% w/w), and drying temperature (60-degrees - 100-degrees-C) were varied but the drying air was kept at constant velocity and humidity.
Characterization of BPN Pyrotechnic Composition Containing Micro- and Nanometer-Sized Boron Particles Koc, Suzan; Ulaş, Abdullah; Yilmaz, Nil Ezgi (Wiley, 2015-10-01) The effect of micro- and nanometer-sized boron particles on boron-potassium nitrate (BPN) ignition composition was investigated in this paper. As a starting point, thermochemical calculations were made to determine the most promising ignition compositions. Both stoichiometric and fuel-rich formulations of BPN were produced to observe the performance variation due to boron content. Particle morphology of boron particles and the surface structure of the ignition compositions were investigated by SEM. The infl...
EFFECT OF VERTICAL SEPARATION DISTANCE ON LAMINAR NATURAL CONVECTIVE HEAT-TRANSFER OVER 2 VERTICALLY SPACED EQUITEMPERATURE HORIZONTAL CYLINDERS Yüncü, Hafit; BATTA, A (Springer Science and Business Media LLC, 1994-04-01) A numerical study of laminar natural convective heat transfer in air from a pair of equi-temperature horizontal cylinders placed one above the other in a vertical plane was carried out. Prime attention was focused on how heat transfer characteristics of the upper cylinder are affected by center-to-center separation distance between two cylinders (CCD). The study was limited to Rayleigh number ranging from 2 x 10(4) to 2 x 10(5) . The vertical center-to-center separation distance between the cylinders was va...
Effect of strain history on simulation of crashworthiness of a vehicle Doğan, Uluğ Çağrı; Gökler, Mustafa İlhan; Department of Mechanical Engineering (2009) In this thesis the sheet metal forming effects such as plastic strain and thickness changes in the crash have been investigated by numerical analysis. The sheet metal forming histories of the components of the load path that absorbs the highest energy during a frontal crash have been considered. To find out the particular load path, the frontal crash analysis of Ford F250 Pickup has been performed at 56 kph into a rigid wall with finite element analysis without considering the forming history. The sheet met...

Citation Formats

J. ZHU, K. O. LEE, A. Yozgatlıgil, and M. Y. CHOI, “Effects of engine operating conditions on morphology, microstructure, and fractal geometry of light-duty diesel engine particulates,” PROCEEDINGS OF THE COMBUSTION INSTITUTE, pp. 2781–2789, 2005, Accessed: 00, 2020. [Online]. Available: https://hdl.handle.net/11511/41427.