Dual frequency bi-orthogonally polarized antenna for GPS applications

Date

2000-01-01

Author

Alatan, Lale
Mahale, A
Balasubramanian, A
Olin, RP

Metadata

Show full item record

This work is licensed under a Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.

Item Usage Stats

240
views

0
downloads

Design, fabrication and testing of dual frequency bi-orthogonally polarized microstrip patch antenna structures for GPS receivers are studied. The considered configurations include orthogonally placed coplanar rectangular patches, orthogonally stacked rectangular patches and stacked square patches. Designed antennas are fabricated according to the optimized parameters, tuned in the presence of radomes and then measured for their bandwidth, input matching, radiation pattern, gain, and polarization characteristics. Comparisons of these different configurations are presented together with theoretical and experimental results.

Subject Keywords

GPS antenna, Bi-orthogonal polarization, Dual frequency, Microstrip antenna

URI

https://hdl.handle.net/11511/54176

Collections

Department of Electrical and Electronics Engineering, Conference / Seminar

Suggestions

OpenMETU
Core

Development of multiband microstrip antennas for GPS applications Önder, Mustafa Caner; Aydın Çivi, Hatice Özlem; Department of Electrical and Electronics Engineering (2019) In this thesis study, the design, fabrication and measurements of dualband and triband circularly polarized microstrip antennas for GPS applications are presented. Characteristic mode analysis technique is applied to get an insight into circularly polarized patch antennas. A design flow is presented for a circularly polarized L1 GPS band microstrip antenna by using characteristic mode analysis. A single fed L1/L2 GPS band right hand circularly polarized four-slotted patch antenna is designed by using reacti...
Beam Switching Reflectarray Monolithically Integrated With RF MEMS Switches Bayraktar, Omer; Aydın Çivi, Hatice Özlem; Akın, Tayfun (2012-02-01) A reflectarray antenna monolithically integrated with 90 RF MEMS switches has been designed and fabricated to achieve switching of the main beam. Aperture coupled microstrip patch antenna (ACMPA) elements are used to form a 10 x 10 element reconfigurable reflectarray antenna operating at 26.5 GHz. The change in the progressive phase shift between the elements is obtained by adjusting the length of the open ended transmission lines in the elements with the RF MEMS switches. The reconfigurable reflectarray is...
Beam Steerable Traveling Wave Meander Line Antenna Using Varactor Diode for X-Band Applications Gokalp, Nihan; Aydın Çivi, Hatice Özlem (2008-07-11) This paper presents a novel beam steerable meander line antenna with varactor diode for X-band applications. Beam steering has been achieved by loading the arms of the meander line antenna with varactor diodes. The capacitances of the varactor diodes have been controlled by DC bias voltage. Instead of varactor diodes, RF-MEMS variable capacitances can be used to scan the beam. Since the insertion loss of MEMS capacitances are small compared to loss of varactor diodes, use of MEMS capacitors will increase th...
Wideband omnidirectional and sector coverage antenna arrays for base stations Alatan, Lale (2018-01-01) By using parallel strip line fed printed dipole antennas as array elements, an omnidirectional antenna array and a wide angle sector coverage array operating in octave band are designed. A maximum deviation of ±1.25 dB from the omnidirectional pattern is achieved for the omnidirectional array, and the average gain of the antenna was measured as being 5 dB in the 1.35–2.7GHz band. For the sector coverage array, a special reflector design is utilized to maintain a half power beam width of around 115◦ with a s...
Reconfigurable antenna structure for RFID system applications using varactor-loading technique Sevinç, Yusuf; Kaya, Adnan (2012-01-01) A novel method is presented for electrically tuning the frequency of a compact radio-frequency identification (RFID) tag antenna. A tuning circuit, comprising a radio frequency (RF) switch and discrete passive components, was completely integrated into the antenna element, which is thus free of DC wires. The low-profile printed antennas were fabricated together with the layouts of the DC control circuits and other RF/baseband circuit footprints. A surface-mounted varactor was applied as a frequency-tuning e...

Citation Formats

L. Alatan, A. Mahale, A. Balasubramanian, and R. Olin, “Dual frequency bi-orthogonally polarized antenna for GPS applications,” 2000, Accessed: 00, 2020. [Online]. Available: https://hdl.handle.net/11511/54176.