EFFECT OF AGING ON MECHANICAL PROPERTIES OF Al-8Si-8Fe-1.4V/SiCp COMPOSITES

2016-01-01
Essari, A.
Sariuglo, F.
Petrovic, Z.
Sedmak, A.
Samardzic, I.
In this study, Al-8Fe-8Si-1.4V/SiCp composites fabricated by squeeze casting process were age-hardened to study the influence of heat treatment on mechanical properties, such as hardness, bending strength and modulus of elasticity. The cast samples were solid soluted at 540 degrees C for one hour, then quenched in water to room temperature, and finally aged at 190 degrees C for 2, 4, 6, 8 and 10 hours for hardness test and at 195 degrees C for 2, 6 and 10 hours for bending strength determination.
METALURGIJA

Suggestions

Effect of swaging on microstructure and tensile properties of W-Ni-Fe alloys
DURLU, NURİ; Caliskan, N. Kaan; Bor, Sakir (Elsevier BV, 2014-01-01)
The objective of this study was to investigate the effect of swaging on the microstructure and tensile properties of high density two phase alloys 90W-7Ni-3Fe and 93W-4.9Ni-2.1Fe. Samples were liquid phase sintered under hydrogen and argon at 1480 degrees C for 30 min and then 15% cold rotary swaged. Measurement of microstructural parameters in the sintered and swaged samples showed that swaging slightly increased tungsten grain size in the longitudinal direction and slightly decreased tungsten grain size i...
Effect of expandable graphite on flame retardant, thermal and mechanical properties of thermoplastic polyurethane composites filled with huntite&hydromagnesite mineral
Guler, Turkan; Tayfun, Umit; Bayramlı, Erdal; DOĞAN, Mehmet (2017-01-10)
The effect of expandable graphite (EG) was studied on the flame retardant, thermal and mechanical properties of thermoplastic polyurethane (TPU) containing huntite&hydromagnesite (HH). According to the flammability tests results, the synergistic interaction was observed between HH and EG. The maximum limiting oxygen index (LOI value was observed at a ratio of 1:1 (HH:EG) and the highest vertical burning test (UL-94) rating of V0 was observed at a ratios of 4:1, 3:2 and 1:1. The synergistic interaction betwe...
Effect of surface roughness in microchannels on heat transfer
Turgay, Metin Bilgehan; Güvenç Yazıcıoğlu, Almıla; Department of Mechanical Engineering (2008)
In this study, effect of surface roughness on convective heat transfer and fluid flow in two dimensional parallel plate microchannels is analyzed by numerically. For this purpose, single-phase, developing, laminar fluid flow at steady state and in the slip flow regime is considered. The continuity, momentum, and energy equations for Newtonian fluids are solved numerically for constant wall temperature boundary condition. Slip velocity and temperature jump at wall boundaries are imposed to observe the rarefa...
Effect of heat treatment on the formation of adiabatic shear bands in high strength steels impacted by AP projectiles
Ubeyli, M.; DEMİR, TEYFİK; Yıldırım, Raif Orhan; Aycan, M. F. (2009-01-01)
This study presents the effect of heat treatment on the adiabatic shear band formation in the steels AISI 4340 and DIN 100Cr6, which were impacted by 7.62 mm armour piercing (AP) projectile. Adiabatic shear band formation was investigated in the steel samples having different hardness levels and thickness values. Examinations were carried out using both optical and scanning electron microscopy to see the microstructural variations apparently. Moreover, microhardness measurements were also made to correlate ...
Effect of Cu addition on the microstructural constituents and mechanical properties of twin roll cast AlFeMnSi alloys
Meydanoglu, Onur; Birbaşar, Onur; Ulus, Ali; Beyhan, Bariş; Kalay, Yunus Eren (2015-01-01)
In this study, the effect of copper addition on microstructural evolution, mechanical and corrosion properties of twin roll cast (TRC) AlFeMnSi alloy system mainly used in container foil applications was investigated. Microstructural characterization studies were conducted on as-cast, homogenization annealed and final products by employing optical and scanning electron microscopes. The mechanical properties of the samples obtained from compositional were determined at the thickness of final product by tensi...
Citation Formats
A. Essari, F. Sariuglo, Z. Petrovic, A. Sedmak, and I. Samardzic, “EFFECT OF AGING ON MECHANICAL PROPERTIES OF Al-8Si-8Fe-1.4V/SiCp COMPOSITES,” METALURGIJA, pp. 189–192, 2016, Accessed: 00, 2020. [Online]. Available: https://hdl.handle.net/11511/68193.