Determination of stress intensity factors in cracked panels reinforced with riveted stiffeners

Download

index.pdf

Date

2012

Author

Sayar, Mehmet Burak

Metadata

Show full item record

Item Usage Stats

190
views

206
downloads

This thesis presents a study about the determination of the stress intensity factors in cracked sheets with riveted stiffeners. Stress intensity factors are determined with both analytical method and finite element method for different combination of rivet/stringer spacing and stringer to sheet stiffness ratio. Analytical part of the thesis is a replication of the original study of Poe which assumes rigid rivet connections with no stringer offset. In the analytical part, the whole systems of equations of Poe are re-derived, and it is shown that there are two typographical errors in the expressions for the calculation of the influence coefficients of the cracked sheet and the stringer. Major objective of the analytical part is to develop a computer code which calculates the variation of the normalized stress intensity factor with the crack length for any combination of rivet/stringer spacing and stringer to sheet stiffness ratio. Analytical part of the study also covers the effect of broken stiffener on the stress intensity factor of the cracked sheet. The stress intensity factors of stiffened cracked sheets are calculated by the finite element method by incorporating fastener flexibility and stringer offset. Finite element solutions are performed by Franc2D/L and Abaqus, and comparisons are made. The effect of geometry, fastener flexibility, and stringer offset on the stress intensity factors are studied by presenting normalized stress intensity factor versus crack length curves. Finally, as a case study a sample damage tolerant stiffened panel is designed according to FAR 25 safety criteria. Experiments are performed for determining mechanical and crack growth properties of Al 2124 which is used as the material in the case study. Present study showed that the most significant effect on the stress intensity factor is seen when stringer-cracked sheet offset is included in the analysis model.

Subject Keywords

Materials of Engineering and Construction., Mechanics of Materials.

URI

http://etd.lib.metu.edu.tr/upload/12614060/index.pdf
https://hdl.handle.net/11511/21448

Collections

Graduate School of Natural and Applied Sciences, Thesis

Suggestions

OpenMETU
Core

Monitoring the Microstructural Evolution in Spheroidized Steels by Magnetic Barkhausen Noise Measurements DAVUT, Kemal; Gür, Cemil Hakan (Springer Science and Business Media LLC, 2010-12-01) The aim of this study is to monitor nondestructively the degree of spheroidization in steels by Magnetic Barkhausen Noise (MBN) method. Various series of specimens consisting of either lamellar pearlite or partially/completely spheroidized carbides were produced from AISI 1060 steel by appropriate heat treatments. All specimens were characterized by metallographic examinations, hardness and MBN measurements. The results show that MBN signals are very sensitive to the variations in the microstructure caused ...
Utilization of Non-destructive Methods for Determining the Effect of Age-Hardening on Impact Toughness of 2024 Al-Cu-Mg Alloy Gür, Cemil Hakan (Springer Science and Business Media LLC, 2008-12-01) The aim of the study is to investigate the correlation between non-destructive measurements and impact toughness of 2024 Al-alloy. Following the solutionizing at 493 degrees C/1 h and water quench, the samples were aged at 190 degrees C for various periods between 0.5 h and 18 h. Hardness, impact toughness, sound velocity, and electrical conductivity were measured for each specimen group, and fracture surfaces were investigated by SEM. To focus on only the effect of precipitation, the process variables were...
Testing and analysis of different hold down devices for CFS construction Pehlivan, Barış Mert; Baran, Eray; Topkaya, Cem (Elsevier BV, 2018-06-01) This paper summarizes the findings of a two-phase study on hold down devices used in cold formed steel (CFS) structural systems. The first phase consisted of component testing and numerical analysis of hold down devices while the second phase was based on testing of CFS framed sheathed wall panels under cyclic lateral loading. Eleven monotonic and three cyclic tensile load tests were performed on seven different types of hold down devices to assess the performance of readily available hold downs and propose...
Comparison of magnetic Barkhausen noise and ultrasonic velocity measurements for microstructure evaluation of SAE 1040 and SAE 4140 steels Gür, Cemil Hakan; Çam, İbrahim (Elsevier BV, 2007-05-01) The aim of this study is to compare the performance of magnetic Barkhausen noise and ultrasonic methods for the evaluation of the microstructure of commercial steels. Following the austenitization of the specimens made of SAE 1040 and SAE 4140, various heat treatments were carried out to obtain microstructures consisting of martensite, tempered martensite, fine pearlite-ferrite, and coarse pearlite-ferrite. The microstructures were initially characterized by SEM investigation and hardness measurements. The ...
Determination of surface residual stresses in carburised AISI 8620 steel by the magnetic Barkhausen noise method Kaleli, T.; Gür, Cemil Hakan (British Institute of Non-Destructive Testing (BINDT), 2020-07-01) Management of the residual stress state is vital for the design and production stages of carburised components in order to satisfy the technical requirements related to performance, fatigue behaviour and useful lifetime. This enforces the use of practical, reliable and time- and cost-effective stress measurement methods by manufacturers. This study aims to investigate the efficiency of the magnetic Barkhausen noise (MBN) method in rapid non-destructive determination of surface residual stresses in carburise...

Citation Formats

M. B. Sayar, “Determination of stress intensity factors in cracked panels reinforced with riveted stiffeners,” M.S. - Master of Science, Middle East Technical University, 2012.