Design of an inertia measurement device for stores

Download

index.pdf

Date

2018

Author

Kılıç, Berkay

Metadata

Show full item record

Item Usage Stats

300
views

155
downloads

In this thesis, design of a device, which can measure mass properties of missiles or their sub-components in a single test setup, is expressed. An object, whose mass properties are going to be calculated, is attached to the device and three-dimensional, oscillatory motion about a specific point is supplied to that object. During this motion, velocity and acceleration values of the object are measured simultaneously with the force and torque values at the connection point. Mass properties of the object are computed by using measured velocity, acceleration, force and torque values in Newton’s equations of motion.

Subject Keywords

Inertia (Mechanics)., Mass (Physics)., Rocketry.

URI

http://etd.lib.metu.edu.tr/upload/12622213/index.pdf
https://hdl.handle.net/11511/27351

Collections

Graduate School of Natural and Applied Sciences, Thesis

Suggestions

OpenMETU
Core

Design of Fuel Cell and Electrolyzer Emulators for Photovoltaic Applications Koubaa, Ahmed; Krichen, Lotfi; Ouali, Abderrazak (2011-09-10) This paper focuses on the design of fuel cell and electrolyzer emulators used for photovoltaic applications. These emulators are based on power electronic circuits. The reference values of the two emulators are taken from fuel cell and electrolyzer mathematical models. In this study, proportional integral regulators are used. A power management is established to ensure a balance between production and consumption. The simulation results show the good performances of the two emulators to produce the electric...
MÜHİMMAT SİSTEMLERİ İÇİN KÜTLE ÖZELLİKLERİ ÖLÇÜMÜ YAPAN TEST DÜZENEĞİ TASARIMI Kılıç, Berkay; Dal, Hüsnü; Tüzün, Aydın (2018-06-29) In this paper, design of a device, which can measure mass properties of missiles or their sub-components in a single test setup, is expressed. An object, whose mass properties are going to be calculated, is attached to the device and three-dimensional, oscillatory motion about a specific point is supplied to that object. During this motion, velocity and acceleration values of the object are measured simultenously with the force and torque values at the connection point of the object. Mass properties of ...
Analysis of the radiation from aparture/printed antennas in the presence of periodic structures through numerical and asymptotic techniques Manara, Giuliano; Aydın Çivi, Hatice Özlem; Nepa, Paolo; Çetin, Ramazan(2010) Proje kapsamında, yakınında saçıcıların bulunduğu elektriksel olarak büyük anten dizilerinin ışıma/saçınma problemini etkin bir şekilde analiz etmek için bir yöntem geliştirmek üzere çalışmalar yapılmıştır. Bu yöntem elektriksel olarak büyük dizilerin asimptotik ışın alan gösterimine ve dizi akımlarının Ayrık Fourier Dönüşüm ifadelerine dayanmaktadır. Gerçekçi anten dizilerinin üzerindeki akım dağılımının Ayrık Fourier Dönüşümünün, dizinin yakınında saçınmaya yol açabilecek nesneler olduğu durumda bile, bel...
Design and fabrication of a high performance resonant MEMS temperature sensor Kose, Talha; Azgın, Kıvanç; Akın, Tayfun (IOP Publishing, 2016-04-01) This paper presents a high performance MEMS temperature sensor comprised of a double-ended-tuning-fork (DETF) resonator and strain-amplifying beam structure. The temperature detection is based on the 'thermal strain induced frequency variations' of the DETF resonator. The major source of thermal strain leading to the frequency shifts is the difference in thermal expansion coefficients of the substrate and the device layers of the fabricated structures. By selecting the substrate as glass and the device laye...
Measurement of the production cross section for a W boson and two b jets in pp collisions at root s=7 TeV Chatrchyan, S.; et. al. (Elsevier BV, 2014-07-01) The production cross section for a Wboson and two b jets is measured using proton-proton collisions at v root s = 7 TeV in a data sample collected with the CMS experiment at the LHC corresponding to an integrated luminosity of 5.0 fb(-1). The W + bbevents are selected in the W..decay mode by requiring a muon with transverse momentum pT> 25GeVand pseudorapidity |eta| 25GeVand |eta| < 2.4. The measured W + bbproduction cross section in the fiducial region, calculated at the level of final-state particles, is...

Citation Formats

B. Kılıç, “Design of an inertia measurement device for stores,” M.S. - Master of Science, Middle East Technical University, 2018.